DTC C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1281 | Detected only during Test Mode. |
|
| 1.CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH/BRAKE PEDAL LOAD SENSING SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List mode on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch / ON or OFF | ON: Brake pedal depressed beyond the specified point OFF: Brake pedal not depressed beyond the specified point | - |
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.
| Result | Proceed to | |
| OK | A | |
| NG | Turning on of the stop light switch is not confirmed. | B |
| Turning on of the brake pedal load sensing switch is not confirmed. | C | |
| The brake pedal load sensing switch turns on first. | D | |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER SENSOR) |
Select the Data List mode on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Master Cylinder Sensor | Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V | When brake pedal released: 0.3 to 0.9 V | Reading increases when the brake pedal depressed. |
Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the intelligent tester changes when the brake pedal is depressed.
|
| ||||
| OK | |
| 4.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | ||
| ||
| 5.INSPECT SKID CONTROL ECU (STP TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A67-2 (STP) - Body ground | Stop light switch on (Brake pedal depressed) | 8 to 14 V |
| A67-2 (STP) - Body ground | Stop light switch off (Brake pedal released) | Below 1.5 V |
|
| ||||
| OK | ||
| ||
| 6.INSPECT SKID CONTROL ECU (FSW+ TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A67-27 (FSW+) - Body ground | Brake pedal load sensing switch off (Brake pedal depressed) | 0.9 to 1.1 kΩ |
| A67-27 (FSW+) - Body ground | Brake pedal load sensing switch on (Brake pedal released) | 192 to 234 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch installation (Click here).
|
| ||||
| OK | ||
| ||