Home › TRANSMISSION ยท U660F AUTOMATIC TRANSAXLE › TRANSMISSION CONTROL CABLE ASSEMBLY

TRANSMISSION CONTROL CABLE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:
Before installing the transmission control cable assembly, check that the park/neutral position switch and shift lever are in neutral.



    C127837
  1. Put the transmission control cable into the cabin and connect the transmission control cable with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    C207570
  1. Connect the transmission control cable to the bracket with a new clip.

  1. Connect the transmission control cable to the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



  1. Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper to lock the nut.

    NOTICE:
    Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.



    C203379E01


    Text in Illustration 
    *1
    Stopper
    *2
    Nut

    HINT:
    If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.



  1. Connect the outer part of the transmission control cable to the shift lever retainer. Check that the stopper returns to the pulled-out position.


    C203380E01


    Text in Illustration 
    *1
    Stopper
    *2
    Nut
    *3
    Shift Lever Retainer
    -
    -



    C203381E01
  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.
    Text in Illustration 
    *1
    Slider
    *2
    Lock Piece



    C204586
  1. Connect the end of the cable to the shift lever.

    NOTICE:
    1. Make sure that the lock piece is pulled up.
    2. Push on the end of the cable all the way to the base of the pin.



    C204598E01
  1. Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.
    Text in Illustration 
    *1
    Cable Rod

  1. Push the lock piece into the adjuster case and lock it.

    NOTICE:
    Make sure that the lock piece is completely locked by the slider.



2. INSTALL FRONT FLOOR COVER


    A130273
  1. Install the floor cover with the 3 clips, bolt and nut.



3. INSTALL AIR CLEANER BRACKET


A208835
  1. Install the bracket with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 ft.*lbf }

  1. Attach the 2 fuel hoses to the bracket.

  1. Attach the 3 wire harness clamps.



    C209709
  1. Connect the glow relay.



    A208834
  1. Install the air cleaner support with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



4. CONNECT FUEL FILTER ASSEMBLY


C209708E01
  1. Slide the fuel filter downward to connect it to the air cleaner bracket.

  1. Install the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Attach the level warning switch connector clamp.

  1. Connect the connector.



5. INSTALL AIR CLEANER CASE


    A208831
  1. Attach the clamp and install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



6. INSTALL AIR CLEANER CAP AND HOSE
  1. Connect the air cleaner hose.



    A208843E01
  1. Attach the 3 clips to install the air cleaner cap.

  1. Connect the PCV hose.

  1. Attach the clamp and connect the mass air flow meter connector.



7. INSTALL NO. 1 ENGINE COVER


    A203808
  1. Attach the 4 clips to install the engine cover.



8. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves in reverse after moving the shift lever to R.
    If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the floor shift assembly installation condition.



9. ADJUST SHIFT LEVER POSITION
  1. Remove the rear console box sub-assembly (Click here).

  1. Apply the parking brake and move the shift lever to N.



    C203381E01
  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.
    Text in Illustration 
    *1
    Slider
    *2
    Lock Piece



    C204598E01
  1. Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.
    Text in Illustration 
    *1
    Cable Rod

  1. Press the lock piece into the adjuster case and lock it.

    NOTICE:
    Make sure that the lock piece is completely locked by the slider.

  1. Inspect the operation of the shift lever (Click here).

  1. Install the rear console box sub-assembly (Click here).



10. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY
  1. Install the rear console box (Click here).