Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0340    Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

for Preparation Click here


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.
The G signal plate (timing sprocket) has one tooth on its outer circumference and is installed on the camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field that generate a voltage in the pickup coil.
The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G signal, and detects the crankshaft angle based on the NE signal.

P0340 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Crank engine for 4 seconds (STA on)
STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more.
(2 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Camshaft timing sprocket
  4. ECM
Idle engine for 1 second (STA off)
STA off:
When either condition below is met for 1 second (1 trip detection logic):
  1. G signal is not input with an engine speed of 650 rpm or more.
  2. No camshaft position sensor signal is sent to the ECM with an engine speed of 650 to 3000 rpm 20 times or more.

HINT:
  1. If DTC P0340 is stored, the following symptoms may appear:
    1. Difficult starting
    2. Misfire
    3. Combustion noise
    4. Black smoke
    5. White smoke
    6. Lack of power


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT CAMSHAFT POSITION SENSOR


    A135405E07
  1. Disconnect the camshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    835 to 1400 Ω
    1 - 2
    Hot
    1060 to 1645 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Camshaft Position Sensor)

    HINT:
    In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).

  1. Reconnect the camshaft position sensor connector.



NG
Go to step 6
OK


2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)


    A130497E05
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B35-1 - B32-80 (G+)
    Always
    Below 1 Ω
    B35-2 - B32-79 (G-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B35-1 or B32-80 (G+) - Body ground
    Always
    10 kΩ or higher
    B35-2 or B32-79 (G-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Camshaft Position Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the camshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 7
OK


3.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)


    A208464E01
  1. Check the sensor installation.

    OK:
    Sensor is installed correctly.



NG
Go to step 8
OK


4.CHECK NO. 2 CAMSHAFT TIMING SPROCKET
  1. Check the condition of the timing sprocket.

    OK:
    Timing sprocket does not have any cracks or deformation.



NG
Go to step 9
OK


5.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 10

6.REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).



NEXT
Go to step 10

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 10

8.SECURELY REINSTALL SENSOR
  1. Securely reinstall the sensor (Click here).



NEXT
Go to step 10

9.REPLACE NO. 2 CAMSHAFT TIMING SPROCKET
  1. Replace the No. 2 camshaft timing sprocket (Click here).


NEXT


10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 4 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END