Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0191    Fuel Rail Pressure Sensor Circuit Range / Performance

for Preparation Click here


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the common rail pressure to the target pressure determined by the ECM. The pressure sensor is a semiconductor that varies its electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the common rail fuel pressure.

A208460E02


P0191 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 1 second
The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more.
(1 trip detection logic)
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor (common rail)
  3. ECM

Related Data List 
DTC No.
Data List
P0191
  1. Fuel Press
  2. Target Common Rail Pressure

WIRING DIAGRAM

Refer to DTC P0087 .

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

  1. Start the engine.

  1. Check the change in the values for the Data List items above when increasing the engine speed from idling to 3000 rpm with no load.

    Result 
    Result
    Proceed to
    Fuel Press is always 10000 kPa or less
    or
    Fuel Press is always 200000 kPa or higher
    A
    Except above
    B

    HINT:
    Normally, "Fuel Press" is +/-15000 kPa of "Target Common Rail Pressure".



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)


    A204374E02
  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B60-5 (PR) - B32-66 (PCR1)
    Always
    Below 1 Ω
    B60-2 (PR2) - B32-114 (PCR2)
    Always
    Below 1 Ω
    B60-1 (VCS) - B32-69 (VCS)
    Always
    Below 1 Ω
    B60-6 (VC) - B32-68 (VCM)
    Always
    Below 1 Ω
    B60-4 (E2) - B32-67 (E2M)
    Always
    Below 1 Ω
    B60-3 (E2S) - B32-91 (E2S)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B60-5 (PR) or B32-66 (PCR1) - Body ground
    Always
    10 kΩ or higher
    B60-2 (PR2) or B32-114 (PCR2) - Body ground
    Always
    10 kΩ or higher
    B60-1 (VCS) or B32-69 (VCS) - Body ground
    Always
    10 kΩ or higher
    B60-6 (VC) or B32-68 (VCM) - Body ground
    Always
    10 kΩ or higher
    B60-4 (E2) or B32-67 (E2M) - Body ground
    Always
    10 kΩ or higher
    B60-3 (E2S) or B32-91 (E2S) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Fuel Pressure Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the ECM connector.



OK
Go to step 5

NG
Go to step 3

3.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0191 is output
    A
    No DTC is output
    B



B
END
A


5.REPLACE COMMON RAIL
  1. Replace the common rail (Click here).


NEXT


6.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0191 is output
    A
    No DTC is output
    B



B
END
A


8.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END