DTC P0112 Intake Air Temperature Circuit Low Input |
DTC P0113 Intake Air Temperature Circuit High Input |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 0.5 seconds | Short in the IAT sensor for 0.5 seconds. (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 0.5 seconds | Open in the IAT sensor for 0.5 seconds. (1 trip detection logic) |
|
| DTC No. | Data List |
| P0112 | Intake Air |
| P0113 |
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (same as actual intake air temperature) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the mass air flow meter connector.
Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
| *1 | MAF Meter |
| *2 | ECM |
| *3 | Front view of wire harness connector (to MAF Meter) |
Reconnect the mass air flow meter connector.
|
| ||||
|
| ||||
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-4 (THA) - B32-110 (THA) | Always | Below 1 Ω |
| B1-5 (E2) - B32-87 (ETHA) | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to MAF Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the mass air flow meter connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
| *1 | MAF Meter |
| *2 | ECM |
Reconnect the mass air flow meter connector.
|
| ||||
|
| ||||
| 5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-4 (THA) or B32-110 (THA) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to MAF Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER. |
Replace the mass air flow meter (Click here).
|
| ||||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM. |
Replace the ECM (Click here).
|
| ||||
| 10.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||