Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

DTC    P0115    Engine Coolant Temperature Circuit

DTC    P0117    Engine Coolant Temperature Circuit Low Input

DTC    P0118    Engine Coolant Temperature Circuit High Input

for Preparation Click here


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.

HINT:
If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the ECT is assumed to be 80°C (176°F).


P0115 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Open or short in the engine coolant temperature (ECT) sensor circuit for 0.5 seconds.
(1 trip detection logic)
  1. Open or short in engine coolant temperature (ECT) sensor circuit
  2. ECT sensor
  3. ECM

P0117 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Short in the ECT sensor circuit for 0.5 seconds.
(1 trip detection logic)
  1. Short in ECT sensor circuit
  2. ECT sensor
  3. ECM

P0118 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Open in the ECT sensor circuit for 0.5 seconds.
(1 trip detection logic)
  1. Open in ECT sensor circuit
  2. ECT sensor
  3. ECM

Related Data List 
DTC No.
Data List
P0115
Coolant Temp
P0117
P0118

HINT:
  1. If DTC P0115, P0117 and/or P0118 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. White smoke
    5. Lack of power
  2. When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

    Reference: 
    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    140°C (284°F) or higher
    Short circuit


WIRING DIAGRAM


A112566E24


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If DTCs relating to different systems are stored and they share terminal E2 as their ground, check this ground circuit first.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    OK:
    75 to 90°C (167 to 194°F) with warm engine.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    75 to 90°C (167 to 194°F)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or more.



B
Go to step 4

C
Go to step 11
A


2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)


    A107691E97
  1. Disconnect the engine coolant temperature (ECT) sensor connector.

  1. Connect terminals 1 and 2 of the ECT sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    ECT Sensor
    *2
    ECM
    *3
    Front view of wire harness connector
    (to ECT Sensor)

  1. Reconnect the ECT sensor connector.



OK
Go to step 7

NG
Go to step 3

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)


    A203950E09
  1. Disconnect the ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B4-2 - B32-111 (THW)
    Always
    Below 1 Ω
    B4-1 - B32-88 (ETHW)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECT Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECT sensor connector.

  1. Reconnect the ECM connector.



OK
Go to step 9

NG
Go to step 8

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)


    A198733E06
  1. Disconnect the ECT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    ECT Sensor
    *2
    ECM

  1. Reconnect the ECT sensor connector.



OK
Go to step 10

NG
Go to step 5

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)


    A112602E55
  1. Disconnect the ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B4-2 or B32-111 (THW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECT Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECT sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


6.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11

7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.
  1. Replace the engine coolant temperature sensor (Click here).



NEXT
Go to step 11

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 11

9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.
  1. Replace the ECM (Click here).



NEXT
Go to step 11

10.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
  1. Replace the engine coolant temperature sensor (Click here).


NEXT


11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END