Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

DTC    P0088    Fuel Rail / System Pressure - Too High

for Preparation Click here


DESCRIPTION


P0088 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After idling for 60 seconds, repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds
The fuel pressure of the common rail exceeds 220000 kPa (2243 kgf/cm2, 319000 psi).
(1 trip detection logic)
  1. Fuel supply pump (suction control valve)
  2. Pressure discharge valve (common rail)
  3. Open or short in fuel supply pump (suction control valve) circuit
  4. ECM

Related Data List 
DTC No.
Data List
P0088
  1. Fuel Press
  2. Target Common Rail Pressure
  3. Injection Pressure Correction
  4. Target Pump SCV Current
  5. Fuel Pressure Relief Valve

HINT:
  1. For more information on the fuel supply pump (suction control valve) and common rail system, refer to System Description (Click here).
  2. When DTC P0088 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

    Reference 
    Engine Speed
    Fuel Press
    Idling
    Approximately 27000 to 45000 kPa
    2500 rpm (No engine load)
    Approximately 50000 to 70000 kPa
  3. When there is an operating problem with the fuel supply pump (when Fuel Press is more than Target Common Rail Pressure due to a problem with the closing of the suction valve), the values of Injection Pressure Correction and Target Pump SCV Current decrease.
  4. Check "Fuel Press", "Target Common Rail Pressure", "Target Pump SCV Current" and "Fuel Pressure Relief Valve" in the freeze frame data.


MONITOR DESCRIPTION

  1. P0088 (Internal fuel pressure too high):
    The ECM stores this DTC if the fuel pressure inside the common rail is more than 220000 kPa (2243 kgf/cm2, 31900 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.
    If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.

WIRING DIAGRAM


A205135E02


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump, the ECM needs initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.

  1. Read the value.

    Standard 
    Engine Speed
    Target Pump SCV Current
    Idling
    923 to 1123 mA
    2500 rpm (No engine load)
    980 to 1212 mA



NG
Go to step 6
OK


2.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

  1. Check the difference in pressure between Fuel Press and Target Common Rail Pressure.

    OK:
    Difference in pressure between Fuel Press and Target Common Rail Pressure is within +/-5000 kPa.



NG
Go to step 5
OK


3.INSPECT PRESSURE DISCHARGE VALVE (COMMON RAIL)
  1. Inspect the pressure discharge valve .



OK
Go to step 12

NG
Go to step 4

4.REPLACE PRESSURE DISCHARGE VALVE (COMMON RAIL)
  1. Replace the common rail (Click here).



NEXT
Go to step 7

5.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)


    A204376E02
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) - B32-41 (PCV+)
    Always
    Below 1 Ω
    B46-2 (PCV) - B32-81 (PCV-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) or B32-41 (PCV+) - Body ground
    Always
    10 kΩ or higher
    B46-2 (PCV) or B32-81 (PCV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Suction Control Valve)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



NG
Go to step 11
OK


6.REPLACE FUEL SUPPLY PUMP
  1. Replace the fuel supply pump (Click here).


NEXT


7.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


8.PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).


NEXT


9.CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. After idling for 60 seconds, repeat engine speed accelerations (from idling to 2500 rpm) for 30 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0088 is output
    A
    No DTC is output
    B



B
END
A


10.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 12

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON and start the engine.

  1. After idling for 60 seconds, repeat engine speed accelerations (from idling to 2500 rpm) for 30 seconds.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P0088.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.


NEXT

END