DTC P1229 Fuel Pump System |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Idling for 60 seconds | The actual fuel pressure exceeds the target fuel pressure by 40000 kPa or higher for 10 seconds. (1 trip detection logic) |
|
| DTC No. | Data List |
| P1229 |
|

| 1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Record the stored DTC and Freeze Frame Data.
| NEXT | |
| 2.CHECK ANY OTHER DTCS OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P1229 | A |
| DTC P1229 and other DTCs | B |
|
| ||||
| A | |
| 3.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT AND PUMP SCV LEARNING VALUE) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current and Pump SCV Learning Value.
Take a snapshot while driving the vehicle under the conditions indicated by the freeze frame data recorded previously.
Read the values of "Target Pump SCV Current" and "Pump SCV Learning Value" in the Data List using the snapshot review function.
Compare "Target Pump SCV Current" and "Pump SCV Learning Value" of the freeze frame data recorded previously with "Target Pump SCV Current" and "Pump SCV Learning Value" of the Data List.
Read the value.
| Result | Proceed to |
| The freeze frame data values are higher than the data list values by 100 mA or more | B |
| Except above | A |
|
| ||||
| A | |
| 4.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.
Check that the internal fuel pressure of the common rail is within the specification below.
|
| ||||
|
| ||||
| 5.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE CONNECTOR - ECM) |
![]() |
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B46-1 (+B) - B32-41 (PCV+) | Always | Below 1 Ω |
| B46-2 (PCV) - B32-81 (PCV-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B46-1 (+B) or B32-41 (PCV+) - Body ground | Always | 10 kΩ or higher |
| B46-2 (PCV) or B32-81 (PCV-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Suction Control Valve) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Clear DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Idle the engine for 60 seconds and run it at 2500 rpm without load for 60 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P1229 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 7.REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
| NEXT | |
| 8.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 9.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 10.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.
Check that the internal fuel pressure of the common rail is within the specification below.
|
| ||||
| OK | |
| 11.CHECK WHETHER DTC OUTPUT RECURS |
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Idle the engine for 60 seconds and run it at 2500 rpm without load for 60 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P1229 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 12.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 13.REPLACE COMMON RAIL (FUEL PRESSURE SENSOR) |
Replace the common rail (Click here).
| NEXT | |
| 14.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
|
| ||||
| 15.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Idle the engine for 60 seconds and run it at 2500 rpm without load for 60 seconds.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1229.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase the idling time.
| NEXT | ||
| ||