Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0045    Turbocharger / Supercharger Boost Control Solenoid Circuit / Open

for Preparation Click here


DESCRIPTION

This DTC indicates that the E-VRV of the turbocharger is malfunctioning. The ECM monitors the E-VRV current to detect an open or short in the E-VRV circuit. If the current is out of the standard range, the ECM stores a DTC and illuminates the MIL immediately.

P0045 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
Open or short in E-VRV circuit for 0.5 seconds or more.
(1 trip detection logic)
  1. E-VRV
  2. Open or short in E-VRV circuit
  3. ECM

HINT:
If DTC P0045 is stored, the following symptoms may appear.

When the nozzle vane of the turbocharger is stuck closed:
- Vehicle surge when driving with full load
When the nozzle vane of the turbocharger is stuck open:
- Lack of power
- Vehicle surge or hesitation under light or medium load
- White smoke

WIRING DIAGRAM


A204373E04


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT E-VRV FOR TURBOCHARGER CONTROL
  1. Inspect the E-VRV for turbocharger control (Click here).



NG
Go to step 5
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE)


    A204588E02
  1. Disconnect the E-VRV connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B44-1 - Body ground
    Ignition switch ON
    10 to 16 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to E-VRV)

  1. Reconnect the E-VRV connector.



NG
Go to step 6
OK


3.CHECK HARNESS AND CONNECTOR (E-VRV - ECM)


    A204370E02
  1. Disconnect the E-VRV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B44-2 - B32-83 (VN)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B44-2 or B32-83 (VN) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to E-VRV)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the E-VRV connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7

5.REPLACE E-VRV
  1. Replace the E-VRV (Click here).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.

    HINT:
    If the voltage at the E-VRV connector is not 11 to 14 V, repair or replace the harness and connector between the E-VRV and the EFI MAIN relay (including the EFI No. 2 fuse).


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END