Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2111/11    Transmitter ID1 Operation Stop

DTC    C2112/12    Transmitter ID2 Operation Stop

DTC    C2113/13    Transmitter ID3 Operation Stop

DTC    C2114/14    Transmitter ID4 Operation Stop

for Preparation Click here


DESCRIPTION

The tire pressure warning valve and transmitter that is installed in the tires and wheels measures the air pressure of the tires. The measured values are transmitted to the tire pressure warning antenna on the body as radio waves and then sent to the tire pressure warning ECU and receiver. The ECU compares the measured air pressure values with the air pressure threshold. When the measured air pressure values are less than this threshold, the warning light in the combination meter turns on.
The tire pressure warning ECU and receiver stores a DTC when the tire pressure warning valve and transmitter stops transmitting signals. At this time, forcibly transmit the signals by releasing the tire pressure rapidly. The stored DTC is cleared when the signal transmission is resumed.

DTC Code
DTC Detection Condition
Trouble Area
C2111/11
C2112/12
C2113/13
C2114/14
Tire pressure warning valve and transmitter stops transmitting signals
  1. Tire pressure warning valve and transmitter
  1. Tire pressure warning ECU and receiver

HINT:
It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM


F101027E06


INSPECTION PROCEDURE

NOTICE:
It is necessary to register an ID code after replacing the tire wheel and/or the tire pressure warning ECU and receiver (Click here).

1.PERFORM FORCED TRANSMISSION OF TRANSMITTER ID OF ALL WHEELS
  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf/cm2, 32 psi)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select "ID Tire Inflation Pressure" by following the prompts displayed on the intelligent tester.

    Tire pressure warning ECU and receiver:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: -100 kPa (-1 kgf/cm2, -14 psi)
    max.: 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire pressure
    If -100 kPa (-1 kgf/cm2, -14 psi) is displayed, the data has not been received.*

    HINT:
    *: It may take about 2 or 3 minutes until the values are displayed.

  1. Rapidly release the pressure from each wheel by approximately 40 kPa (0.4 kgf/cm2, 5.8 psi) for 30 seconds or more.

    1. Check that the tire pressure data displayed on the intelligent tester screen changes.

      OK:
      The tire pressure data displayed on the intelligent tester screen changes with the value of the tire pressure.

      NOTICE:
      1. When the "ID Tire Inflation Pressure" data (IDs 1 to 4) changes, reset the tire pressure of the tires to the specified value, rotate the tires 90 to 270° and recheck.

    2. After confirming that the tire pressure data displayed on the intelligent tester screen has changed, set the pressure of each tire to the specified value.

      Standard pressure:
      220 kPa (2.2 kgf/cm2, 32 psi)

      HINT:
      If the tire pressure data displayed on the intelligent tester screen has not changed after rechecking, go to the troubleshooting procedures of DTCs C2121/21 to C2124/24 which indicate transmission or reception malfunctions (Click here).



NG
CHECK OTHER PROBLEM (MALFUNCTION IN TRANSMISSION OR RECEPTION FUNCTION)
OK

END