Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

DTC    P2121    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here


DESCRIPTION

Refer to DTC P2120 .

P2121 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON
  1. Accelerator pedal fully closed for 3 seconds
  2. Accelerator pedal open partway for 3 seconds
  3. Accelerator pedal fully open for 3 seconds
The difference between VPA and VPA2 is below 0.4 V, or higher than 1.2 V for 0.5 seconds.
(1 trip detection logic)
  1. Accelerator pedal position sensor circuit
  2. Accelerator pedal position sensor
  3. ECM

Related Data List 
DTC No.
Data List
P2121
  1. Accel Position
  2. Accel Sens. No.1 Volt %
  3. Accel Sens. No.2 Volt %

WIRING DIAGRAM

Refer to DTC P2120 .

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)


    C129061E02
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

  1. Read the values.

    Standard Voltage:
    Accelerator Pedal
    Accel Sens. No.1 Volt %
    Accel Sens. No.2 Volt %
    Released
    8 to 28%
    51 to 86%
    Depressed
    30 to 55%
    73 to 98%

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A200913E04
  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A6-1 (VCP2) - A12-57 (VCP2)
    Always
    Below 1 Ω
    A6-2 (EPA2) - A12-58 (EPA2)
    Always
    Below 1 Ω
    A6-3 (VPA2) - A12-54 (VPA2)
    Always
    Below 1 Ω
    A6-4 (VCPA) - A12-55 (VCPA)
    Always
    Below 1 Ω
    A6-5 (EPA) - A12-56 (EPA)
    Always
    Below 1 Ω
    A6-6 (VPA) - A12-53 (VPA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A6-1 (VCP2) or A12-57 (VCP2) - Body ground
    Always
    10 kΩ or higher
    A6-2 (EPA2) or A12-58 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A6-3 (VPA2) or A12-54 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A6-4 (VCPA) or A12-55 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A6-5 (EPA) or A12-56 (EPA) - Body ground
    Always
    10 kΩ or higher
    A6-6 (VPA) or A12-53 (VPA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Accelerator Pedal Position Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON.

  1. Fully close the accelerator pedal for 3 seconds or more, then hold it partway open for 3 seconds or more, then fully open it for 3 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P2121 is output
    A
    No DTC is output
    B



B
END
A


5.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Fully close the accelerator pedal for 3 seconds, then hold it partway open for 3 seconds, then fully open it for 3 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END