DTC B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1655/37 | When one of following conditions is met:
|
|

| 1.CHECK FOR DTC |
![]() |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the driver side seat inner belt.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor and the driver side seat inner belt.
Using a service wire, connect K1-12 (DBE-) and K1-11 (DBE+)*1 or L18-12 (DBE-) and L18-11 (DBE+)*2 of connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K3-4 (LBE+) - K3-3 (LBE-) | Below 1 Ω |
| Tester Connection | Specified Condition |
| L16-4 (RBE+) - L16-3 (RBE-) | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K3-4 (LBE+) - K3-3 (LBE-) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L16-4 (RBE+) - L16-3 (RBE-) | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| K3-3 (LBE-) - Body ground | Below 1 V |
| K3-4 (LBE+) - Body ground | Below 1 V |
| Tester Connection | Specified Condition |
| L16-3 (LBE-) - Body ground | Below 1 V |
| L16-4 (LBE+) - Body ground | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| K3-3 (LBE-) - Body ground | 1 MΩ or higher |
| K3-4 (LBE+) - Body ground | 1 MΩ or higher |
| Tester Connection | Specified Condition |
| L16-3 (LBE-) - Body ground | 1 MΩ or higher |
| L16-4 (LBE+) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK DRIVER SIDE SEAT INNER BELT ASSEMBLY |
![]() |
Connect the connectors to the center airbag sensor and the driver side seat inner belt.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 8.REPLACE DRIVER SIDE SEAT INNER BELT ASSEMBLY |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the driver side seat inner belt (Click here).
| NEXT | |
| 9.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||