Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0715    Input / Turbine Speed Sensor Circuit Malfunction

DTC    P0717    Input Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the turbine which indicates the input speed of the transaxle. By comparing the input turbine speed (speed sensor NT) signal with the counter gear speed (speed sensor NC) signal, the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

C206302E01


Text in Illustration 
*1
Counter Gear
*2
Clutch Drum
*3
Speed Sensor NC
*4
Speed Sensor NT

DTC Code
DTC Detection Condition
Trouble Area
P0715
When the speed sensor input voltage is either higher than 1.9 V or below 0.1 V for 4.5 seconds or more (1-trip detection logic).
  1. Speed sensor NT (speed sensor)
  2. Transmission wire
  3. TCM
P0717
TCM detects conditions (a), (b) and (c) continuously for 5 sec. or more (1-trip detection logic):
(a) Vehicle speed: 50 km/h (31 mph) or more
(b) Park/neutral position switch (R) and STA signal are OFF
(c) Speed sensor NT: less than 300 rpm

MONITOR DESCRIPTION

The NT terminal of the TCM detects a pulse signal from the speed sensor NT (input RPM). The TCM calculates gear shifts by comparing the signal from speed sensor NT with the signal from speed sensor NC.
While the vehicle is operating in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is more than 1000 rpm*2, the TCM interprets this as a fault, illuminates the MIL and stores the DTC.

HINT:
  1. *1: A pulse is not output or is irregularly output.
  2. *2: The vehicle speed is 50 km/h (31 mph) or more.


WIRING DIAGRAM


C206310E01


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NT)
    Input turbine speed (speed sensor NT)/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up on (after warming up the engine): Value from speed sensor NT equal to engine speed
    2. Lock-up off (idling with shift lever in N): Value from speed sensor NT nearly equal to engine speed
    The data is displayed in increments of 50 rpm.
    NT Sensor Voltage
    Input turbine speed sensor output voltage (speed sensor NT)/
    Min.: 0 V
    Max.: 5 V
    Engine idling: 0.1 to 1.9 V
    -

    HINT:
    1. SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.
    2. SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR NT INSTALLATION


    C206303
  1. Make sure that the connector is properly connected, and check the speed sensor installation.

    OK:
    The installation bolts are tightened properly and there is no clearance between the sensor and transaxle case.



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR NT (Click here)
OK


2.INSPECT TRANSMISSION WIRE


    C206824E01
  1. Disconnect the speed sensor connector.

  1. Remove the TCM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    NTB speed sensor side - 1 (NTB) TCM side
    Always
    Below 1 Ω
    NTO speed sensor side - 2 (NTO) TCM side
    Always
    Below 1 Ω
    NTB speed sensor side - Body ground
    Always
    10 kΩ or higher
    NTO speed sensor side - Body ground
    Always
    10 kΩ or higher
    NTB speed sensor side - All other terminals except 1 (NTB) TCM side
    Always
    10 kΩ or higher
    NTO speed sensor side - All other terminals except 2 (NTO) TCM side
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Transmission Wire
    *2
    Speed Sensor Side
    *3
    TCM Side



NG
REPLACE TRANSMISSION WIRE (Click here)
OK


3.REPLACE SPEED SENSOR NT (SPEED SENSOR)
  1. Replace the speed sensor (Click here).


NEXT


4.CHECK IF DTC OUTPUT RECURS (DTC P0715 OR P0717)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / DTC / Clear.

    HINT:
    Write down the currently output DTCs before clearing them.

  1. Perform the monitor drive pattern (Click here).

  1. Enter the following menus: Powertrain / ECT / DTC.

  1. Read the DTCs using the intelligent tester.
    Result 
    Result
    Proceed to
    Only P0715 or P0717 is output
    A
    DTCs are not output
    B



B
END
A

REPLACE TCM (Click here)