Home › HEATER & AIR CONDITIONING SYSTEM › HEATER › COMBUSTION TYPE POWER HEATER SYSTEM

DTC    016    Difference Evaluation 2

DTC    020    Glow Plug Malfunction

DTC    021    Glow Plug Output Overload

DTC    022    Glow Plug Output Error

DTC    025    Short in K-line Circuit

DTC    030    Abnormal Combustion Air Blower Motor Speed

DTC    031    Combustion Air Blower Motor Malfunction

DTC    032    Short in Combustion Air Blower Motor Circuit

DTC    034    Combustion Air Blower Motor Output Error

DTC    060    Overheating Control Sensor Malfunction

DTC    061    Short in Overheating Control Sensor Circuit

DTC    064    Flame Sensor Malfunction

DTC    065    Short in Flame Sensor Circuit

DTC    071    Surface Sensor Malfunction

DTC    072    Short in Surface Sensor Circuit

DTC    074    ECU Overheating

DTC    090    ECU Internal Malfunction / Reset Detection

DTC    091    Repeated Resets Detection

DTC    092    ROM Error

DTC    093    RAM Error

DTC    094    Transistor Malfunction

DTC    095    Software Stuck Overflow

DTC    096    Operation Locked Detection

DTC    097    ECU Defects

DTC    098    Main Relay Malfunction

DTC    099    EEPROM Error

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
016
The difference in temperatures detected by the surface sensor and temperature control sensor is 30°C (86°F) or higher.
  1. Heater assembly (Surface sensor)
  2. Heater assembly (Temperature control sensor)
020
Operation stop of the glow plug is detected (open in the circuit).
  1. Heater assembly (Glow plug)
  2. Heater assembly (Harness or connector)
021
Overload on the glow plug or a short in the wire harness that is connected to the glow plug is detected.
  1. Heater assembly (Glow plug)
  2. Heater assembly (Harness or connector)
022
An error is detected in the output from the ECU to the glow plug, or a problem with the wire harness that is connected to the glow plug is detected.
  1. Heater assembly (ECU)
  2. Heater assembly (Harness or connector)
025
A short circuit is detected in the diagnostic communication line in the heater assembly.
  1. Heater assembly
  2. Heater assembly (Harness or connector)
030
Air blower motor speed is out of the allowable range (8800 rpm to 10400 rpm) (an object may be caught in or between parts around the air blower motor).
Heater assembly (Air blower motor)
031
Operation stop of the air blower motor is detected (open in the circuit).
  1. Heater assembly (Air blower motor)
  2. Heater assembly (Harness or connector)
032
A short circuit is detected in the wire harness which is connected to the air blower motor.
Heater assembly (Harness or connector)
034
An error is detected in the output from the ECU to the air blower motor, or a problem with the wire harness that is connected to the air blower motor is detected.
  1. Heater assembly (ECU)
  2. Heater assembly (Harness or connector)
060
Operation stop of the temperature control sensor is detected (open in the circuit).
Heater assembly (Temperature control sensor)
061
A short is detected in the temperature control sensor circuit.
  1. Heater assembly (Temperature control sensor)
  2. Heater assembly (Harness or connector)
064
Operation stop of the flame sensor is detected (open in the circuit).
Heater assembly (Flame sensor)
065
A short is detected in the flame sensor circuit.
  1. Heater assembly (Flame sensor)
  2. Heater assembly (Harness or connector)
071
Operation stop of the surface sensor is detected (open in the circuit).
Heater assembly (Surface sensor)
072
A short is detected in the surface sensor circuit.
  1. Heater assembly (Surface sensor)
  2. Heater assembly (Harness or connector)
074
The ECU stops operating due to overheating.
Heater assembly (ECU)
090
An internal malfunction of the control unit is detected.
Heater assembly (ECU)
091
Reset operation is repeated too many times.
Heater assembly (ECU)
092
A control unit (ROM) error is detected.
Heater assembly (ECU)
093
A control unit (RAM) error is detected.
Heater assembly (ECU)
094
A transistor malfunction due to frequent operation interruptions is detected.
Heater assembly (ECU)
095
A software stuck overflow is detected.
Heater assembly (ECU)
096
An operation lock due to the absence of a valid process is detected.
Heater assembly (ECU)
097
An internal control unit malfunction is detected.
Heater assembly (ECU)
098
A main relay malfunction is detected.
Heater assembly (ECU)
099
An EEPROM error is detected.
Heater assembly (ECU)

INSPECTION PROCEDURE

1.CHECK HEATER ASSEMBLY
  1. Clear the DTCs stored in the memory using the DTC tester (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
REPLACE HEATER ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)