Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System)

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU is stuck on HI output, the ECM outputs this DTC.

DTC Code
DTC Detection Condition
Trouble Area
B279A
When communication line (EFIO-IMI) between ECM and transponder key ECU is stuck on HI output for 6 seconds or more
  1. Wire harness
  2. Transponder key ECU
  3. ECM

WIRING DIAGRAM


B160072E14


INSPECTION PROCEDURE

1.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTC (Click here).
    Result 
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B

    HINT:
    If any DTCs other than B279A are output, troubleshoot those DTCs first.



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
E180672E08
  1. Disconnect the E50 ECU connector.

  1. Disconnect the A12 ECM connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E50-13 (EFIO) - A12-16 (IMI)
    Always
    Below 1 Ω
    E50-13 (EFIO) or A12-16 (IMI) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E50-13 (EFIO) - Body ground
    Always
    Below 1 V
    A12-16 (IMI) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK TRANSPONDER KEY ECU (OUTPUT)


    B169769E10
  1. Measure waveform.
    Waveform 1 (Reference) 
    Tester Connection
    Tool Setting
    Switch Condition
    E50-13 (EFIO) - E50-16 (GND)
    10 V/DIV., 100 msec./DIV.
    Ignition switch ON

    OK:
    Waveform is output normally (see illustration).

    Result 
    Result
    Proceed to
    OK (for 2AD-FHV)
    A
    OK (for 2AD-FTV)
    B
    NG
    C



B
REPLACE ECM (Click here)

C
Go to step 5
A

REPLACE ECM (Click here)  

5.CHECK TRANSPONDER KEY ECU (POWER SOURCE AND BODY GROUND)


    B128338E59
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E50-1 (+B) - E50-16 (GND)
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE TRANSPONDER KEY ECU
Replace the transponder key ECU.

NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.


NEXT


8.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


9.CHECK FOR DTC
  1. Clear the DTC (Click here).
    Result 
    Result
    Proceed to
    DTC B279A is not output
    A
    DTC B279A is output (for 2AD-FHV)
    B
    DTC B279A is output (for 2AD-FTV)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (TRANSPONDER KEY ECU IS DEFECTIVE)