Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

DTC    P011C    Charge Air Temperature/Intake Air Temperature Correlation (Bank 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P0112 .
Refer to DTC P1496 .

P011C 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After engine completely warmed up, allow engine to soak for long time (8 hours or more).
Start the engine and idle the engine for 3 minutes or more.
After the engine is completely warmed up and then allowed to soak for a long time (8 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 15°C (59°F) or higher.
(2 trip detection logic)
  1. Open or short in intake air temperature (IAT) sensor circuit
  2. Open or short in intake air temperature sensor (turbo) circuit
  3. IAT sensor (built into mass air flow meter)
  4. intake air temperature sensor (turbo)
  5. ECM

Related Data List 
DTC No.
Data List
P011C
  1. Intake Air
  2. Intake Air Temp (Turbo)

WIRING DIAGRAM

Refer to DTC P0112 .
Refer to DTC P1496 .

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P011C)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P011C is output
    A
    P011C and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Allow the engine to soak for 1 to 2 hours.

    HINT:
    1. It is not necessary to allow the engine to soak if the engine is cold.
    2. The engine cools faster if the hood is opened.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.

  1. Read the value.

    OK:
    The difference between the displayed value and outside air temperature is below 5°C (9°F).

    NOTICE:
    If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.


NEXT


3.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    OK:
    The difference between the displayed value and outside air temperature is below 15°C (27°F).



NG
Go to step 6
OK


4.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE [TURBO])
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

  1. Read the value.

    OK:
    The difference between the displayed value and outside air temperature is below 15°C (27°F).



NG
Go to step 8
OK


5.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    A204469E06
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B1-4 (THA) - B32-110 (THA)
    Always
    Below 1 Ω
    B1-5 (E2) - B32-87 (ETHA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B1-4 (THA) or B32-110 (THA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to MAF Meter)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
Go to step 10
OK


7.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).



NEXT
Go to step 11

8.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)


    A204916E03
  1. Disconnect the intake air temperature sensor (turbo) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A49-2 - B32-113 (THIA)
    Always
    Below 1 Ω
    A49-1 - B32-90 (ETHI)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A49-2 or B32-113 (THIA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Intake Air Temperature Sensor (Turbo))
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the intake air temperature sensor (turbo) connector.

  1. Reconnect the ECM connector.



NG
Go to step 10
OK


9.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
  1. Replace the intake air temperature sensor (turbo) (Click here).



NEXT
Go to step 11

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Allow the engine to soak for 1 to 2 hours.

    HINT:
    1. It is not necessary to allow the engine to soak if the engine is cold.
    2. The engine cools faster if the hood is opened.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.

  1. Read the value.

    NOTICE:
    If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).

  1. Read the value.

    OK:
    The difference between the displayed value and outside air temperature is below 15°C (27°F).


NEXT

END