Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

DTC    P245C    EGR Cooler Bypass Control Circuit Low

DTC    P245D    EGR Cooler Bypass Control Circuit High

for Preparation Click here


DESCRIPTION

The EGR cooler VSV is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

P245C 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
Open or short in the EGR cooler VSV for 3 seconds.
(1 trip detection logic)
  1. Open or short in EGR cooler VSV circuit
  2. EGR cooler VSV
  3. ECM

P245D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
Open or short in the EGR cooler VSV for 3 seconds.
(1 trip detection logic)
  1. Open or short in EGR cooler VSV circuit
  2. EGR cooler VSV
  3. ECM

WIRING DIAGRAM


A204373E06


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.INSPECT EGR COOLER VSV
  1. Inspect the EGR cooler VSV (Click here).



NG
Go to step 5
OK


2.CHECK EGR COOLER VSV (POWER SOURCE CIRCUIT)


    A204918E02
  1. Disconnect the EGR cooler VSV connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B53-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to EGR Cooler VSV)

  1. Reconnect the EGR cooler VSV connector.



NG
Go to step 6
OK


3.CHECK HARNESS AND CONNECTOR (EGR COOLER VSV - ECM)


    A205134E02
  1. Disconnect the EGR cooler VSV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B53-2 - B32-106 (ECBV)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B53-2 or B32-106 (ECBV) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to EGR Cooler VSV)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the EGR cooler VSV connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7

5.REPLACE EGR COOLER VSV
  1. Replace the EGR cooler VSV (Click here).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR

HINT:
If the voltage at the EGR cooler VSV connector is not 11 to 14 V, repair or replace the harness and connector between the EGR cooler VSV and EFI MAIN relay (including the EFI No. 2 fuse).

  1. Repair or replace the harness or connector.


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 3 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END