Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

DTC    P2141    Diesel Throttle Motor Circuit Low

DTC    P2142    Diesel Throttle Motor Circuit High

for Preparation Click here


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body.

P2141 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle the engine for 5 seconds or more
The throttle actuator current is below 0.5 A for 2.0 seconds during EGR valve operation.
(1 trip detection logic)
  1. Open or short in throttle actuator circuit
  2. Diesel throttle valve assembly
  3. ECM

P2142 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle the engine for 5 seconds or more
An throttle actuator current of 8 A or higher due to a mechanical malfunction, or a Hall IC temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic)
  1. Open or short in throttle actuator circuit
  2. Diesel throttle valve assembly
  3. ECM

DTC No.
Data List
P2141
Throttle Motor DUTY
P2142

WIRING DIAGRAM


A209871E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.INSPECT DIESEL THROTTLE BODY ASSEMBLY
  1. Inspect the diesel throttle body assembly (Click here).



NG
Go to step 4
OK


2.CHECK HARNESS AND CONNECTOR (ECM - DIESEL THROTTLE BODY)


    A107944E56
  1. Disconnect the diesel throttle body assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B107-2 (M+) - B32-42 (M+)
    Always
    Below 1 Ω
    B107-1 (M-) - B32-43 (M-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B107-2 (M+) or B32-42 (M+) - Body ground
    Always
    10 kΩ or higher
    B107-1 (M-) or B32-43 (M-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Diesel Throttle Body Assembly)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the diesel throttle body assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


3.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 6

4.REPLACE DIESEL THROTTLE BODY ASSEMBLY
  1. Replace the diesel throttle body assembly (Click here).



NEXT
Go to step 6

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Idle the engine for 5 seconds or more

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END