Home › TRANSMISSION ยท U660F AUTOMATIC TRANSAXLE › PARK / NEUTRAL POSITION SWITCH

PARK / NEUTRAL POSITION SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


C135732
  1. Install the park/neutral position switch to the control shaft.

  1. Temporarily install the 2 bolts.

  1. Temporarily install the control shaft lever.



    C206496E01
  1. Turn the lever clockwise until it stops, and then turn it counterclockwise 2 notches.

  1. Remove the control shaft lever.



    C135733E08
  1. Align the protrusions of the park/neutral position switch.

  1. Hold the switch in that position and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    Text in Illustration 
    *1
    Protrusion



    C136685
  1. Install the control shaft lever to the control shaft with the washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Connect the park/neutral position switch connector.



2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C205890
  1. Connect the transmission control cable to the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



3. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves in reverse after moving the shift lever to R.
    If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the floor shift assembly installation condition.



4. ADJUST SHIFT LEVER POSITION
  1. Remove the rear console box sub-assembly (Click here).

  1. Apply the parking brake and move the shift lever to N.



    C203381E01
  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.
    Text in Illustration 
    *1
    Slider
    *2
    Lock Piece



    C204598E01
  1. Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.
    Text in Illustration 
    *1
    Cable Rod

  1. Press the lock piece into the adjuster case and lock it.

    NOTICE:
    Make sure that the lock piece is completely locked by the slider.

  1. Inspect the operation of the shift lever (Click here).

  1. Install the rear console box sub-assembly (Click here).



5. INSTALL AIR CLEANER BRACKET


A208835
  1. Install the bracket with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 ft.*lbf }

  1. Attach the 2 fuel hoses to the bracket.

  1. Attach the 3 wire harness clamps.



    C209709
  1. Connect the glow relay.



    A208834
  1. Install the air cleaner support with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



6. CONNECT FUEL FILTER ASSEMBLY


C209708E01
  1. Slide the fuel filter downward to connect it to the air cleaner bracket.

  1. Install the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Attach the level warning switch connector clamp.

  1. Connect the connector.



7. INSTALL AIR CLEANER CASE


    A208831
  1. Attach the clamp and install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



8. INSTALL AIR CLEANER CAP AND HOSE
  1. Connect the air cleaner hose.



    A208843E01
  1. Attach the 3 clips to install the air cleaner cap.

  1. Connect the PCV hose.

  1. Attach the clamp and connect the mass air flow meter connector.



9. INSTALL NO. 1 ENGINE COVER


    A203808
  1. Attach the 4 clips to install the engine cover.



10. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Apply the parking brake and turn the ignition switch to ON.

  1. Depress the brake pedal and check that the engine can be started when the shift lever is in N or P, but does not start when the shift lever is in other positions.

  1. Check that the back-up light illuminates and the reverse warning buzzer sounds when the shift lever is in R, but do not function when the shift lever is in other positions.
    If a malfunction or failure is found, check the park/ neutral position switch.