ECD SYSTEM > Turbocharger Oil Leak and White Smoke |
| Oil Leak Type | Description | Main Trouble Area |
| Internal oil leak (White smoke) | Oil leak from bearing housing to compressor housing (intake side) or turbine housing (exhaust side) through seal rings. Internal oil leak is not visible from outside of turbocharger. If oil leak occurs from turbine side seal, large amount of white smoke will be emitted from exhaust pipe. |
|
| External oil leak | Oil leak from inside of turbocharger to outside of turbocharger (e.g. from FIPG seal, oil pipe flange or oil pipe union). Includes oil leak visible from outside of turbocharger. |
|




| Faults and Symptoms of Turbocharger Parts |
| Main fault | Seal ring breakage | |
| Symptoms |
| |
| Note |
| |
| Main fault | Seal ring breakage | |
| Symptoms |
| |
| Note |
| |
| Main fault | Oil drain clogging by coked oil | |
| Symptoms | Large amount of white smoke from exhaust pipe | |

| Main fault |
| |
| Symptoms |
| |
| Note |
| |
| Main fault | Breakage | |
| Symptoms |
| |
| Note |
| |
| Symptoms | Oil leak from FIPG sealing part | |
| Note |
| |

| Symptoms | Oil leak from hose connection between hose and compressor housing | |
| Note | If oil stain is traced to hose connection part, it can be determined to be due to hose connection failure. | |

| 1.CHECK TYPE OF OIL LEAK |
Check whether the oil leak is an internal or external oil leak.
| Oil Leak Type | Description |
| Internal oil leak (White smoke) | Oil leak from bearing housing to compressor housing (intake side) or turbine housing (exhaust side) through seal rings. Internal oil leak is not visible from outside of turbocharger. If oil leak occurs from turbine side seal, large amount of white smoke will be emitted from exhaust pipe. |
| External oil leak | Oil leak from inside of turbocharger to outside of turbocharger (e.g. from FIPG seal, oil pipe flange or oil pipe union). Includes oil leaks visible from outside of turbocharger. |
| Result | Proceed to |
| External oil leak | A |
| Internal oil leak | B |
|
| ||||
| A | |
| 2.REPLACE THE PART WHICH IS LEAKING OIL |
Replace the part which is leaking oil.
| NEXT | ||
| ||
| 3.CHECK WHITE SMOKE |
Fully depress the accelerator pedal and then release it.
![]() |
Check whether white smoke is emitted or not when racing the engine.
| Result | Proceed to |
| White smoke is emitted | A |
| White smoke is not emitted | B |
|
| ||||
| A | |
| 4.READ OUTPUT DTC (RELATED TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| Result | Proceed to |
| No DTCs are output | A |
| DTCs related to engine are output | B |
|
| ||||
| A | |
| 5.CHECK WHEN WHITE SMOKE IS EMITTED |
![]() |
Check whether the white smoke is emitted only just after engine start and disappears later, or not.
| Result | Proceed to |
| Yes (White smoke is emitted only just after engine start) | A |
| No (White smoke is always and continuously emitted) | B |
|
| ||||
| A | |
| 6.CHECK TEMPERATURE WHEN WHITE SMOKE IS EMITTED |
Check whether the white smoke is emitted only in cold weather when the temperature is less than 0 °C (32°F).
| Result | Proceed to |
| Yes (White smoke is emitted in only cold conditions) | A |
| No (White smoke is emitted in both cold and warm conditions) | B |
|
| ||||
| A | |
| 7.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE) |
Inspect the glow plug assembly .
|
| ||||
| OK | |
| 8.INSPECT FUEL INJECTOR COMPENSATION CODE |
Read the injector compensation codes .
|
| ||||
| OK | |
| 9.INSPECT DIESEL INJECTION SYSTEM |
Check the injectors, common rail and supply pump.
|
| ||||
| OK | |
| 10.CHECK EGR VALVE ASSEMBLY |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / EGR Close Lrn. Status.
Read the value.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
When changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.
Remove the EGR valve assembly (Click here).
Visually check the EGR valve for deposits.
If there are deposits, clean the EGR valve.
![]() |
Hold the EGR valve up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.
|
| ||||
| OK | |
| 11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Check the engine speed during the Active Test.
|
| ||||
|
| ||||
| 12.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER |
Check the cylinder compression pressure .
|
| ||||
| OK | |
| 13.REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
| NEXT | |
| 14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 15.INSPECT COMPRESSOR INLET |
Remove the air cleaner hose from the compressor inlet.
Check whether an excessive amount of oil is present or not, and whether excessive oil deposits are attached to the compressor impeller or not.
| NEXT | |
| 16.INSPECT COMPRESSOR OUTLET |
Remove the air hose from the compressor outlet.
Check whether an excessive amount of oil or excessive oil deposits are present or not at the compressor outlet.
| Result | Proceed to |
| Excessive amount of oil present at both compressor inlet and outlet | A |
| Excessive amount of oil present only at compressor outlet | B |
| Excessive amount of oil not present at compressor inlet or outlet | C |
|
| ||||
|
| ||||
| C | |
| 17.INSPECT TURBINE INLET |
Remove the turbocharger from the engine.
Check whether an excessive amount of wet oil or excessive oil deposits are present at the turbine inlet.
| NEXT | |
| 18.INSPECT TURBINE OUTLET |
Check whether an excessive amount of wet oil or excessive oil deposits are present at the turbine outlet.
| Result | Proceed to |
| Excessive amount of oil present at both turbine inlet and outlet | A |
| Excessive amount of oil present only at turbine outlet | B |
|
| ||||
| B | |
| 19.REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
| NEXT | |
| 20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||