Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0011    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0012    Camshaft Position "A" - Timing Over-Retarded (Bank 1)

for Preparation Click here


DESCRIPTION

HINT:
If DTC P0011 or P0012 is output, check the VVT (Variable Valve Timing) system.

The VVT system includes the ECM, oil control valve and VVT controller. The ECM sends a target duty cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure applied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A156445E22


DTC No.
DTC Detection Condition
Trouble Area
P0011
The valve timing is not adjusted in the valve timing advance range (1 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly for intake camshaft
  3. Camshaft timing gear assembly
  4. ECM
P0012
The valve timing is not adjusted in the valve timing retard range (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly for intake camshaft
  3. Camshaft timing gear assembly
  4. ECM

WIRING DIAGRAM

Refer to DTC P0010 .

INSPECTION PROCEDURE

HINT:
  1. DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC remains stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0011 and/or P0012 is output
    A
    DTC P0011 or P0012 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A200906E01
  1. Remove the camshaft timing oil control valve assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Camshaft Timing Oil Control Valve)



    A183795E07
  1. Apply positive (+) battery voltage to terminal 1 and negative (-) battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the oil control valve.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
  1. Inspect the camshaft timing gear assembly .



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


4.ADJUST VALVE TIMING

HINT:
There are no marks on the cylinder head to align for the purpose of checking valve timing. Valve timing can only be inspected by aligning the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and reinstall the chain to align the timing marks .


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Allow the engine to idle for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0011 or P0012 is output
    B

    HINT:
    DTC P0011 or P0012 is output when foreign objects in the engine oil are caught in some parts of the system. These codes remain stored for a short time even after the system returns to normal. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



B
REPLACE ECM (Click here)
A

SYSTEM IS OK