DTC P0617 Starter Relay Circuit High |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0617 | When conditions (a), (b) and (c) are met, a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):
|
|


| 1.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM |
Check if the vehicle is equipped with an entry and start system.
| Result | Proceed to |
| w/o Entry and Start System | A |
| w/ Entry and Start System | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to ON and when the engine is cranking.
| Condition | Starter Signal |
| Ignition switch ON | OFF |
| Engine cranking | ON |
| Result | Proceed to |
| OK | A |
| NG (for Manual Transaxle) | B |
| NG (for CVT) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 3.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the ignition switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Any terminals | Off | 10 kΩ or higher |
| 2 (AM1) - 1 (ST1) | START | Below 1 Ω |
| *1 | Component without harness connected (Ignition Switch Assembly) |
Reconnect the ignition switch assembly connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM) |
![]() |
Disconnect the ECM connector.
Disconnect the ignition switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E5-1 (ST1) or A12-48 (STA) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (Ignition Switch Assembly) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
Reconnect the ignition switch assembly connector.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY) |
![]() |
Disconnect the ECM connector.
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 1 or A12-48 (STA) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reinstall the ST relay.
|
| ||||
| OK | ||
| ||
| 6.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the ignition switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Any terminals | Off | 10 kΩ or higher |
| 2 (AM1) - 1 (ST1) | START | Below 1 Ω |
| *1 | Component without harness connected (Ignition Switch Assembly) |
Reconnect the ignition switch assembly connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the park/neutral position switch connector.
Disconnect the ignition switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E5-1 or B28-4 - Body ground | Always | 10 kΩ or higher |
Reconnect the park/neutral position switch connector.
Reconnect the ignition switch assembly connector.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY) |
![]() |
Disconnect the park/neutral position switch connector.
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 1 or B28-9 - Body ground | Always | 10 kΩ or higher |
Reconnect the park/neutral position switch connector.
Reinstall the relay.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY) |
Remove the ST relay from the No. 7 relay block (for LHD).
![]() |
Remove the ST relay from the No. 8 relay block (for RHD).
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 1 or A12-48 (STA) - Body ground | Always | 10 kΩ or higher |
Reinstall the ST relay.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 10.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is ON and when the engine is cranking.
| Condition | Starter Signal |
| Ignition switch ON | OFF |
| Engine cranking | ON |
| Result | Proceed to |
| OK | A |
| NG (for Manual Transaxle) | B |
| NG (for CVT) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - MAIN BODY ECU) |
![]() |
Disconnect the clutch start switch assembly connector.
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-2 or E20-3 (STR) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Clutch Start Switch Assembly) |
| *2 | Front view of wire harness connector (to Main Body ECU) |
Reconnect the clutch start switch assembly connector.
Reconnect the main body ECU connector.
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY) |
![]() |
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 1 or A4-1 - Body ground | Always | 10 kΩ or higher |
Reinstall the ST relay.
Reconnect the clutch start switch assembly connector.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM) |
![]() |
Disconnect the ECM connector.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A12-48 (STA) or A4-1 - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Clutch Start Switch Assembly) |
| *2 | Front view of wire harness connector (to ECM) |
Reinstall the ECM connector.
Reconnect the clutch start switch assembly connector.
|
| ||||
| OK | ||
| ||
| 14.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - MAIN BODY ECU) |
![]() |
Disconnect the park/neutral position switch connector.
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B28-4 or E20-3 (STR) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Park/Neutral Position Switch) |
| *2 | Front view of wire harness connector (to Main Body ECU) |
Reconnect the park/neutral position switch connector.
Reconnect the main body ECU connector.
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY) |
![]() |
Disconnect the park/neutral position switch connector.
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 1 or B28-9 - Body ground | Always | 10 kΩ or higher |
Reconnect the park/neutral position switch connector.
Reinstall the relay.
|
| ||||
| OK | |
| 16.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the park/neutral position switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B28-9 or A12-48 (STA) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Park/Neutral Position Switch) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the park/neutral position switch connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||