AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Follow the instructions on the tester and read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| SPD (NC) | Counter gear speed/ Min.: 0 rpm Max.: 12,750 rpm | 3rd gear when shift lever is on D (after warming up the engine); Intermediate shaft speed (NC) becomes close to the engine speed | Data is displayed in increments of 50 rpm |
| SPD (NT) | Input turbine speed/ Min.: 0 rpm Max.: 12,750 rpm |
| Data is displayed in increments of 50 rpm |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | Shift lever is: P or N: ON Except P or N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Stop Light Switch | Stop light switch status/ ON or OFF |
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd, 4th and 5th | Shift lever position is:
| - |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF | Shift lever is: R: ON Except R: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (P Range) | PNP switch status/ ON or OFF | Shift lever is: P: ON Except P: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (N Range) | PNP switch status/ ON or OFF | Shift lever is: N: ON Except N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (D Range) | PNP switch status/ ON or OFF | Shift lever is: 4 or D: ON Except 4 or D: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (4 or D) | PNP switch status/ ON or OFF | Shift lever is: 4: ON Except 4: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (3 Range) | PNP switch status/ ON or OFF | Shift lever is: 3: ON Except 3: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (2 Range) | PNP switch status/ ON or OFF | Shift lever is: 2 or L: ON Except 2 or L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (L Range) | PNP switch status/ ON or OFF | Shift lever is: L: ON Except L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| A/T Oil Temperature 1 | ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or "150°C (302°F) or more", ATF temperature sensor circuit is open or short circuited |
| Lock Up | Lock up status/ ON or OFF |
| - |
| Lock Up Solenoid Status | Lock-up solenoid status/ ON or OFF |
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| - |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | [Test Details] Operate shift solenoid valve and set each shift lever position by yourself [Vehicle Condition]
| 1st / 2nd / 3rd / 4th / 5th | Possible to check operation of shift solenoid valves |
| Activate the Solenoid (S4) | [Test Details] Operate the shift solenoid S4 [Vehicle Condition]
| ON / OFF | - |
| Activate the Solenoid (SL1) | [Test Details] Operate the shift solenoid SL1 [Vehicle Condition]
| ON / OFF | - |
| Activate the Solenoid (SL2) | [Test Details] Operate the shift solenoid SL2 [Vehicle Condition]
| ON / OFF | - |
| Activate the Solenoid (SL3) | [Test Details] Operate the shift solenoid SL3 [Vehicle Condition]
| ON / OFF | - |
| Activate the Lock Up | [Test Details] Control shift solenoid DSL to set automatic transaxle to the lock-up condition [Vehicle Condition]
| ON / OFF | Possible to check shift solenoid valve DSL operation |
| Activate the Solenoid (DSL) | [Test Details] Operate the shift solenoid DSL [Vehicle Condition]
| ON / OFF | - |
| Activate the Solenoid (SR) | [Test Details] Operate the shift solenoid SR [Vehicle Condition]
| ON / OFF | - |
| Activate the Solenoid (SLT)* | [Test Details] Operate shift solenoid SLT and raise line pressure [Vehicle Condition]
| ON / OFF | - |