DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0705 | When one of following conditions is met: (A) Any 2 or more of the P, N, R, D, 3 and 2 input signals are ON simultaneously (2 trip detection logic) (B) Any 2 or more of the NSW R, D, 3 and 2 input signals are ON simultaneously (2 trip detection logic) (C) When both conditions below are met (2 trip detection logic)
|
|

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | Shift lever is: P or N: ON Except P or N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF | Shift lever is: R: ON Except R: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (P Range) | PNP switch status/ ON or OFF | Shift lever is: P: ON Except P: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (N Range) | PNP switch status/ ON or OFF | Shift lever is: N: ON Except N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (4 or D) | PNP switch status/ ON or OFF | Shift lever is: 4 or D: ON Except 4 or D: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (3 Range) | PNP switch status/ ON or OFF | Shift lever is: 3: ON Except 3: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (2 Range | PNP switch status/ ON or OFF | Shift lever is: 2 or L: ON Except 2 or L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift SW Status (L Range) | PNP switch status/ ON or OFF | Shift lever is: L: ON Except L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| 1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the park/neutral position switch connector.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B28-2 (RB) - Body ground | Ignition Switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B28-4 (B) - Body ground | Ignition Switch ON | 11 to 14 V |
| Result | Proceed to |
| OK | A |
| NG | B |
|
| ||||
| A | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Shift Position | Specified Condition |
| 4 - 5 | P and N | Below 1 Ω |
| Except P and N | 10 kΩ or higher | |
| 2 - 6 | P | Below 1 Ω |
| Except P | 10 kΩ or higher | |
| 2 - 1 | R | Below 1 Ω |
| Except R | 10 kΩ or higher | |
| 2 - 9 | N | Below 1 Ω |
| Except N | 10 kΩ or higher | |
| 2 - 7 | D | Below 1 Ω |
| Except D | 10 kΩ or higher | |
| 2 - 3 | 2 | Below 1 Ω |
| Except 2 | 10 kΩ or higher | |
| 2 - 8 | L | Below 1 Ω |
| Except L | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Connect the park/neutral position switch connector.
Disconnect the ECM connector.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Shift Position | Specified Condition |
| B96-24 (P) - Body ground | P | 11 to 14 V |
| Except P | Below 1 V | |
| B96-25 (R) - Body ground | R | 11 to 14 V* |
| Except R | Below 1 V | |
| B96-27 (N) - Body ground | N | 11 to 14 V |
| Except N | Below 1 V | |
| B96-26 (D) - Body ground | D or 4 | 11 to 14 V |
| Except D or 4 | Below 1 V | |
| B96-29 (3) - Body ground | 3 | 11 to 14 V |
| Except 3 | Below 1 V | |
| B96-28 (2) - Body ground | 2 or L | 11 to 14 V |
| Except 2 or L | Below 1 V |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL UNIT) |
![]() |
Disconnect the transmission control switch connector.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Shift Position | Specified Condition |
| 1 (NSSD) - Body ground | D and 4 | 11 to 14 V |
| Except D and 4 | Below 1 V | |
| 5 (NSSL) - Body ground | 2 and L | 11 to 14 V |
| Except 2 and L | Below 1 V |
|
| ||||
| OK | |
| 6.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Shift Position | Specified Condition |
| 1 (NSSD) - 2 (AT3) | Except 4 and 3 | 10 kΩ or higher |
| 4 and 3 | Below 1 Ω | |
| 5 (NSSL) - 6 (ATL) | Except L | 10 kΩ or higher |
| L | Below 1 Ω |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM) |
![]() |
Connect the transmission control switch connector.
Disconnect the ECM connector.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
| A12-25 (4) - Body ground | 4 | 11 to 14 V |
| Except 4 | Below 1 V | |
| A12-26 (L) - Body ground | L | 11 to 14 V |
| Except L | Below 1 V |
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Turn the ignition switch OFF.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B28-4 (B) - B96-62 (NSW) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B28-4 (B) or B96-62 (NSW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||