DTC P0340 Camshaft Position Sensor Circuit Malfunction |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 |
|
|
| P0342 | The output voltage of the camshaft position sensor is 0.3 V or less for 5 seconds (1 trip detection logic). |
|
| P0343 | The output voltage of the camshaft position sensor is 4.7 V or higher for 5 seconds (1 trip detection logic). |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0340, P0342 OR P0343) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0340, P0342 or P0343 is output | A |
| DTC P0340, P0342 or P0343 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT (SENSOR POWER SOURCE) |
![]() |
Disconnect the camshaft position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B123-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
| *1 | Front view of wire harness connector (to Camshaft Position Sensor) |
Reconnect the camshaft position sensor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT - ECM) |
![]() |
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B123-1 (VV1+) - B32-94 (G2+) | Always | Below 1 Ω |
| B123-2 (VV1-) - B32-118 (G2-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B123-1 (VV1+) or B32-94 (G2+) - Body ground | Always | 10 kΩ or higher |
| B123-2 (VV1-) or B32-118 (G2-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Camshaft Position Sensor) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the camshaft position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT) |
![]() |
Check the camshaft position sensor installation.
|
| ||||
| OK | |
| 5.CHECK INTAKE CAMSHAFT |
Check the teeth of the intake camshaft.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT |
Replace the camshaft position sensor for intake camshaft (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0340, P0342 or P0343 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 8.ADJUST VALVE TIMING |
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0340, P0342 or P0343 are output | B |
|
| ||||
| A | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT - ECM) |
![]() |
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B123-3 (VC) - B32-119 (VCV1) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B123-3 (VC) or B32-119 (VCV1) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Camshaft Position Sensor) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the camshaft position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||