Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0516    Battery Temperature Sensor Circuit Low

DTC    P0517    Battery Temperature Sensor Circuit High

for Preparation Click here


DESCRIPTION

A110648E01
The battery temperature sensor installed on the battery current sensor detects the battery temperature.
A thermistor is integrated into the battery temperature sensor, and the resistance of the thermistor in the battery temperature sensor changes according to the battery temperature.
The resistance of the thermistor in the battery temperature sensor decreases as the battery temperature increases. The resistance increases as the temperature decreases.
The battery temperature sensor is connected to the ECM. The ECM supplies 5 V from the THB terminal to the battery temperature sensor through resistor R.
The battery temperature sensor and resistor R are connected in series. This results in fluctuations in the voltage supplied from the THB terminal when the resistance changes according to the battery temperature.
The ECM determines the battery temperature according to fluctuations in voltage. When the battery temperature is high, the ECM reduces the amount of current supplied from the generator in order to protect the battery.

DTC No.
DTC Detection Condition
Trouble Area
P0516
The battery temperature sensor output value is 0.2 V or less for 0.5 seconds or more with the ignition switch ON (1 trip detection logic).
  1. Short in battery temperature sensor circuit
  2. Battery temperature sensor (built into battery current sensor assembly)
  3. ECM
P0517
The battery temperature sensor output value is 4.8 V or higher for 0.5 seconds or more with the ignition switch ON (1 trip detection logic).
  1. Open in battery temperature sensor circuit
  2. Battery temperature sensor (built into battery current sensor assembly)
  3. ECM

WIRING DIAGRAM

Refer to DTC P1550 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT BATTERY CURRENT SENSOR ASSEMBLY


    A210605E02
  1. Disconnect the battery current sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (THB) - 4 (E2)
    24 to 26°C (75 to 79°F)
    1.91 to 2.065 kΩ

    Text in Illustration 
    *1
    Component without harness connected
    (Battery Current Sensor Assembly)



NG
REPLACE BATTERY CURRENT SENSOR ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR - ECM)


    A207278E01
  1. Disconnect the battery current sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B31-1 (THB) - A12-54 (THB)
    Always
    Below 1 Ω
    B31-4 (E2) - B32-68 (EIB)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Always
    Specified Condition
    B31-1 (THB) or A12-54 (THB) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Battery Current Sensor Assembly)
    *2
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR - ECM)
OK

REPLACE ECM (Click here)