Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD

RADIO ANTENNA CORD > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


B129872
  1. Using a screwdriver, detach the 4 clips and 6 claws, and then remove the instrument cluster finish panel.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE COMBINATION METER ASSEMBLY


B136780
  1. Remove the 2 screws.

  1. Pull the combination meter in the direction indicated by the arrow in the illustration to detach the 2 clips.

  1. Disconnect the connector and remove the combination meter.



4. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208365
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208366
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



6. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)
  1. Remove the radio receiver with bracket (Click here).



7. REMOVE STEREO OPENING COVER (w/o Radio Receiver)


B133002
  1. Remove the 4 bolts.

  1. Detach the 4 clips and remove the stereo opening cover.



8. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. for HDD:
    Remove the radio receiver with bracket .

  1. for DVD:
    Remove the radio receiver with bracket .



9. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY CENTER


    B129890
  1. Using a moulding remover, detach the 5 clips and remove the instrument panel register.



10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    B129889E04
  1. Open the glove compartment door.

  1. Detach the claw from the glove compartment door stopper.

  1. While pushing in the sides of the glove compartment door in the direction indicated by the arrows in the illustration, open the door to release it from the 2 stoppers.



    B129888
  1. Open the door as much as possible.

  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.



11. REMOVE FRONT PILLAR GARNISH LH
  1. for Short Body:
    Remove the front pillar garnish .

  1. for Long Body:
    Remove the front pillar garnish .



12. REMOVE FRONT PILLAR GARNISH RH
  1. for Short Body:
    Remove the front pillar garnish .

  1. for Long Body:
    Remove the front pillar garnish .



13. REMOVE UPPER INSTRUMENT PANEL


    B129886
  1. Remove the 2 bolts from the passenger airbag.

  1. Disconnect the passenger airbag connector.

  1. Remove the 2 bolts and 2 screws.

  1. Disconnect the connector and detach the clamp.



  1. Detach the 6 clips and 5 claws and remove the instrument panel.


    B208364



14. REMOVE ANTENNA CORD SUB-ASSEMBLY


  1. for 3ZR-FAE (w/ Radio Receiver):



    1. Disconnect the connector.


      B223293

    2. Detach the 4 clamps and remove the antenna cord.



  1. except 3ZR-FAE & for 3ZR-FAE (w/o Radio Receiver):



    1. Disconnect the connector.


      B222152

    2. Detach the 4 clamps and remove the antenna cord.



15. REMOVE ROOF HEADLINING ASSEMBLY
  1. for Shot Body:
    Remove the roof headlining (Click here).

  1. for Long Body:
    Remove the roof headlining (Click here).



16. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY


  1. for Short Body (w/o Sliding Roof):



    1. Apply masking tape to the antenna cord to mark it.


      B134704E01

      HINT:
      Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.

    2. Remove the antenna cord from the roof headlining.

    3. Remove the double-sided tape from the roof headlining.



  1. for Short Body (w/ Sliding Roof):



    1. Apply masking tape to the antenna cord to mark it.


      B134706E01

      HINT:
      Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.

    2. Remove the antenna cord from the roof headlining.

    3. Remove the double-sided tape from the roof headlining.



  1. for Long Body (w/o Sliding Roof):



    1. Apply masking tape to the antenna cord to mark it.


      B134708E01

      HINT:
      Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.

    2. Remove the antenna cord from the roof headlining.

    3. Remove the double-sided tape from the roof headlining.



  1. for Long Body (w/ Sliding Roof):



    1. Apply masking tape to the antenna cord to mark it.


      B134710E01

      HINT:
      Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.

    2. Remove the antenna cord from the roof headlining.

    3. Remove the double-sided tape from the roof headlining.