Home › TRANSMISSION ยท U140F AUTOMATIC TRANSAXLE › DIFFERENTIAL OIL SEAL

DIFFERENTIAL OIL SEAL > REPLACEMENT

for Preparation Click here



1. REPLACE TRANSAXLE HOUSING OIL SEAL LH
  1. Drain the automatic transaxle fluid.

    1. Remove the drain plug and gasket, and drain ATF.

    2. Install a new gasket and drain plug.

      Torque:
      47 N*m{ 479 kgf*cm , 35 ft.*lbf }

  1. Remove the front drive shaft LH (Click here).



    D025835E01
  1. Remove the transaxle housing oil seal LH.

    1. Using SST, tap out the oil seal.

      SST
      09308-00010  



    D025836E01
  1. Install the transaxle housing oil seal LH.

    1. Coat the lip of a new oil seal with MP grease.

    2. Using SST and a hammer, tap in the oil seal.

      SST
      09726-27012   (09726-02041)
      09950-70010   (09951-07200)

      Standard depth:
      -0.5 to 0.2 mm (-0.0196 to 0.00787 in.)

      NOTICE:
      Do not damage the lip of the oil seal.

  1. Install the front drive shaft LH (Click here).

  1. Add automatic transaxle fluid.

    Fluid type:
    Toyota Genuine ATF WS

  1. Inspect the transaxle fluid level (Click here).



2. REPLACE TRANSAXLE HOUSING OIL SEAL RH
  1. Remove the engine assembly with transaxle.

    1. for 1AZ-FE:
      Remove the engine with transaxle (Click here).

    2. for 2AZ-FE:
      Remove the engine with transaxle (Click here).

  1. Drain the automatic transaxle fluid.

    1. Remove the drain plug and gasket, and drain ATF.

    2. Install a new gasket and the drain plug.

      Torque:
      47 N*m{ 479 kgf*cm , 35 ft.*lbf }

  1. Remove the 3 bolts and drive shaft bearing bracket.

  1. Remove the 3 bolts and engine mount bracket RR.

  1. Remove the transfer assembly .



    D025618E01
  1. Remove the transaxle housing oil seal RH (Outside).

    1. Using a screwdriver with its tip wrapped with vinyl tape, pry out the oil seal.

      NOTICE:
      Be careful not to damage the housing.



    C139837E02
  1. Remove the transaxle housing oil seal RH (Inside).

    1. Using SST, tap out the oil seal.

      SST
      09308-00010  

      NOTICE:
      Be careful not to damage the differential case.



    C188860E01
  1. Install the transaxle housing oil seal RH (Inside).

    1. Coat the lip of a new oil seal with the MP grease.

    2. Using SST and a hammer, tap in the oil seal.

      SST
      09950-60010   (09951-00410)
      09950-70010   (09951-07200)

      Standard depth:
      27.5 to 28.5 mm (1.09 to 1.12 in.)

      NOTICE:
      Do not damage the lip of the oil seal.



    C188861E01
  1. Install the transaxle housing oil seal RH (Outside).

    1. Coat the lip of a new oil seal with MP grease.

    2. Using SST and a hammer, tap in the oil seal.

      SST
      09649-17010  
      09950-70010   (09951-07200)

      Standard depth:
      5.5 to 6.5 mm (0.217 to 0.255 in.)

      NOTICE:
      Do not damage the lip of the oil seal.

  1. Install the transfer assembly .

  1. Install the engine mount bracket RR with the 3 bolts.

    Torque:
    64 N*m{ 652 kgf*cm , 47 ft.*lbf }

  1. Install the drive shaft bearing bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. Install the engine assembly with transaxle.

    1. for 1AZ-FE:
      Install the engine with transaxle (Click here).

    2. for 2AZ-FE:
      Install the engine with transaxle (Click here).

  1. Add automatic transaxle fluid.

    Fluid type:
    Toyota Genuine ATF WS

  1. Inspect the fluid level (Click here).