RADIATOR > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
![]() |
Install the radiator to the fan shroud with cooling fan with the 2 bolts.
![]() |
Install the No. 1 radiator hose to the radiator.
Install the No. 2 water by-pass hose and No. 2 radiator hose to the radiator.

![]() |
w/ Air Conditioning System:
Install the cooler condenser to the fan shroud with cooling fan.
![]() |
Attach the 2 claws to install the No. 2 fan shroud.
Install the 2 bolts.
![]() |
Install the radiator together with the 2 lower radiator supports.
| 2. INSTALL UPPER RADIATOR SUPPORT BRACKET |
![]() |
Install the 2 upper radiator support brackets with the 2 bolts.
| 3. CONNECT COOLER REFRIGERANT LIQUID PIPE (w/ Air Conditioning System) |
![]() |
Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.
Install the O-ring on the liquid pipe sub-assembly.
Install the liquid pipe sub-assembly on the cooler condenser with the bolt.
| 4. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Air Conditioning System) |
![]() |
Remove the attached vinyl tape from the hose and the connecting part of the cooler condenser.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.
Install the O-ring on the cooler refrigerant discharge hose.
Install the cooler refrigerant discharge hose on the cooler condenser with the bolt.
| 5. INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY |
![]() |
Install the reinforcement with the 2 bolts.
| 6. INSTALL FRONT BUMPER CENTER STAY SUB-ASSEMBLY |
![]() |
Install the stay with the 2 bolts.
| 7. CONNECT HORN CONNECTOR |
![]() |
Connect the 2 horn connectors.
| 8. CONNECT WIRE HARNESS |
w/o Hood Courtesy Switch:
Attach the wire harness with the 4 clamps.
Connect the 2 fan motor connectors.

w/ Hood Courtesy Switch:
Attach the wire harness with the 5 clamps.
Connect the 2 fan motor connectors.
Connect the hood courtesy switch connector.

| 9. CONNECT NO. 2 WATER BY-PASS HOSE |
![]() |
Connect the No. 2 water by-pass hose to the radiator reservoir.
| 10. INSTALL NO. 1 WATER BY-PASS PIPE |
Install the No. 1 water by-pass pipe to the upper radiator support with the 2 bolts.
| 11. INSTALL NO. 5 WATER BY-PASS HOSE |
Install the by-pass hose to the radiator and No. 1 water by-pass pipe.
| 12. INSTALL NO. 1 WATER BY-PASS HOSE |
Install the by-pass hose to the radiator reservoir and No. 1 water by-pass pipe.

| 13. CONNECT NO. 2 RADIATOR HOSE |
![]() |
Connect the No. 2 radiator hose to the water inlet housing.
| 14. CONNECT NO. 1 RADIATOR HOSE |
![]() |
Connect the 2 radiator hoses.
Install the 2 bolts.
| 15. INSTALL BATTERY |
| 16. INSTALL BATTERY CLAMP |
![]() |
Attach the hook of the battery clamp to the front battery bracket.
Partially tighten the nut and temporarily install the bolt.
Adjust the battery clamp position.
Tighten the nut and bolt.
| 17. INSTALL GENERATOR ASSEMBLY |
Install the generator (Click here).
| 18. INSTALL FRONT BUMPER COVER |
w/ Hood Moulding:
Install the front bumper cover (Click here).
w/ Under Guard:
Install the front bumper cover (Click here).
w/o Under Guard:
Install the front bumper cover (Click here).
| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 20. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
![]() |
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening until it is filled to the B line at the base of the reservoir filler neck.
| Item | Specified Condition |
| for Manual Transaxle | 5.8 liters (6.1 US qts, 5.1 Imp. qts) |
| for CVT | 6.0 liters (6.3 US qts, 5.3 Imp. qts) |
Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine and warm it up until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Condition |
| Manual Air Conditioning System | Fan speed: Any setting except off Temperature: Toward WARM Air conditioning switch: Off |
| Automatic Air Conditioning System | Temperature: Toward MAX (HOT) Air conditioning switch: Off |
Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.
Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines. If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 21. CHARGE REFRIGERANT (w/ Air Conditioning System) |
Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).

| 22. WARM UP ENGINE (w/ Air Conditioning System) |
Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging the refrigerant.
| 23. INSPECT FOR REFRIGERANT LEAK (w/ Air Conditioning System) |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation under these conditions:
![]() |
Using a gas leak detector, check the refrigerant line for leakage.
If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.
Disconnect the connector and leave the pressure switch on for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.
| 24. INSPECT FOR COOLANT LEAK |
Remove the radiator reservoir cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Warm up the engine.
Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.
Reinstall the radiator reservoir cap.
| 25. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Install the under cover with the 6 screws and 10 clips.
| 26. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Attach the 4 clips to install the cover.