Home › TRANSMISSION ยท E352F / E359F MANUAL TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY

MANUAL TRANSAXLE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL MANUAL TRANSAXLE CASE PROTECTOR


D030076E02
  1. Install the case protector with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL MANUAL TRANSAXLE ASSEMBLY


D025747E02
  1. Align the input shaft with the clutch disc and install the transaxle to the engine.

  1. Install the 10 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf } for bolt A
    46 N*m{ 469 kgf*cm , 34 ft.*lbf } for bolt B
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for bolt C



3. INSTALL STIFFENER PLATE RH


C127241
  1. Install the stiffener plate with the 4 bolts.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }



4. INSTALL STIFFENER PLATE LH


C127240
  1. Install the stiffener plate with the 4 bolts.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }



5. INSTALL OIL PAN INSULATOR


C127239
  1. Install the insulator with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



6. INSTALL REAR ENGINE MOUNTING BRACKET


C132314
  1. Install the bracket with the 3 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



7. INSTALL ENGINE MOUNTING BRACKET LH


C129226
  1. Install the bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



8. INSTALL FRONT ENGINE MOUNTING BRACKET


C129224
  1. Install the bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



9. INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY


C127255
  1. Connect the 2 cable ends with the 2 washers and 2 clips.

  1. Install 2 new clips to the control cable bracket.



10. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
  1. 1AZ-FE:
    Install the clutch release cylinder (Click here).

  1. 2AZ-FE:
    Install the clutch release cylinder (Click here).



11. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
  1. Install the back-up light switch and gasket to the manual transaxle case.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }



    D026905E01
  1. Connect the back-up light switch connector.



12. INSTALL TRANSFER ASSEMBLY


    C126622
  1. except K111F:
    Install the transfer to the transaxle with the 6 nuts and 2 bolts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }



    C130224
  1. for K111F:
    Install the transfer to the transaxle with the 6 nuts and 2 bolts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }



13. INSTALL ENGINE ASSEMBLY WITH MANUAL TRANSAXLE
  1. for 1AZ-FE:
    Install the engine with manual transaxle (Click here).

  1. for 2AZ-FE:
    Install the engine with manual transaxle (Click here).



14. ADD TRANSAXLE OIL


15. INSPECT TRANSAXLE OIL
  1. Stop the vehicle in a level place.

  1. Remove the transaxle filler plug and gasket.



    D025304E21
  1. Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transaxle oil.

    Oil grade:
    GL-4

    Viscosity:
    SAE 75W

    Standard capacity:
    2.5 liters (2.6 US qts, 2.2 Imp. qts)

    NOTICE:
    1. Too much or too little oil will lead to transaxle problems.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transaxle filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



16. ADD TRANSFER OIL


17. INSPECT TRANSFER OIL


    C110905
  1. Remove the transfer case plug No. 2 (for filler) and gasket.

  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.
    If the result is not as specified, add transfer oil.

    Oil grade:
    Hypoid gear oil SX API GL-5 or equivalent

    Viscosity:
    SAE 85W-90

    Standard capacity:
    0.45 liter (0.48 US qts, 0.40 Imp. qts)

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leakage.

  1. Install a new gasket into the case plug (for filler) and then install the plug.

    Torque:
    39 N*m{ 398 kgf*cm , 28 ft.*lbf }



18. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL