NAVIGATION SYSTEM (for DVD) > Illumination Circuit |


| 1.CHECK ILLUMINATION |
Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch. | A |
| Illumination comes on for all components except navigation receiver assembly. | B |
| No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.). | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY) |
![]() |
Disconnect the E10 spiral cable connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E10-12 (IL+2) - Body ground | Light control switch in TAIL or HEAD | 11 to 14 V |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly (Click here).
Connect the positive (+) lead of the battery to terminal 5 (IL+2) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch connector.

Check if the illumination for the steering pad switch comes on.
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Remove the spiral cable sub-assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 8 (EAU) - 4 (EAU) | Centered | Below 1 Ω |
| Rotated 2.5 times to the left | ||
| Rotated 2.5 times to the right | ||
| 5 (IL+2) - 12 (IL+2) | Centered | Below 1 Ω |
| Rotated 2.5 times to the left | ||
| Rotated 2.5 times to the right |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - SPIRAL CABLE) |
for 3ZR-FAE:
![]() |
Disconnect the E106 navigation receiver assembly connector.
![]() |
Disconnect the E10 spiral cable connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E106-6 (SWG) - E10-4 (EAU) | Always | Below 1 Ω |
| E106-6 (SWG) - Body ground | Always | 10 kΩ or higher |
except 3ZR-FAE:
![]() |
Disconnect the E56 navigation receiver assembly connector.
![]() |
Disconnect the E10 spiral cable connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E56-6 (SWG) - E10-4 (EAU) | Always | Below 1 Ω |
| E56-6 (SWG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BATTERY) |
![]() |
Disconnect the E52 navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E52-10 (ILL+) - Body ground | Light control switch in TAIL or HEAD | 11 to 14 V |
|
| ||||
| OK | ||
| ||