DTC P1603 Engine Stall History |
DTC P1605 Rough Idling |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1603 | After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic). |
|
| DTC No. | DTC Detection Condition | Trouble Area |
| P1605 | After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). |
|
| Symptom | Suspected Area |
| Engine vibration occurs and engine stops | Air-fuel ratio abnormal |
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Rough idling after engine started | Air-fuel ratio abnormal, abnormal combustion |

| Vehicle State | Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Idling or decelerating | Slowly decreases and engine stalls | Air-fuel ratio abnormal | Air suction |
| 3 to 6 |
| Sensor malfunction (value from sensor too lean) |
| 7 to 16 | |||
| Sensor malfunction (value from sensor too rich) | 25 to 34 | ||||
| Fuel supply problem |
| 17 to 24 | |||
| Intake air volume insufficient | ISC flow rate |
| 35 to 37 | ||
| Excessive valve overlap |
| 38 | |||
| Ignition timing incorrect | Does not operate as expected |
| 39 to 41 | ||
| Rapidly decreases and engine stalls | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 42, 43 | |
| External part malfunctioning | Increase in load |
| 44 to 49 | ||
| Accelerating | - | Crankshaft position sensor, camshaft position sensor malfunction | Power temporarily cut |
| 1 |
| Mass air flow meter | Foreign matter adhesion |
| 50 | ||
| Fuel supply problem | Fuel leak, clog |
| 53 to 55 | ||
| Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 51, 52 | ||

| Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Slowly decreases and engine stalls | Air-fuel ratio abnormal | Air suction |
| 3 to 6 |
| Sensor malfunction (value from sensor too lean) |
| 7 to 16 | ||
| Sensor malfunction (value from sensor too rich) | 25 to 34 | |||
| Fuel supply problem |
| 17 to 24 | ||
| Intake air volume insufficient | ISC flow rate |
| 35 to 37 | |
| Ignition timing incorrect | Does not operate as expected |
| 39 to 41 | |
| Rapidly decreases and engine stalls | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 42, 43 |
| External part malfunctioning | Increase in load |
| 44 to 49 | |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Read the DTCs (Click here).
| Result | Proceed to |
| Only DTC P1603 and P1605 are output | A |
| DTCs other than P1603 and P1605 are output | B |
|
| ||||
| A | |
| 2.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Problem Symptom | Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | ||
| Closed Throttle Position SW | Engine Speed | Total of Short FT and Long FT | |||
| When idling or decelerating, engine speed slowly decreases and engine stalls | All 5 sets of freeze frame data are ON | Decreases slowly*1 | All 5 sets of freeze frame data are +15% or more*2 |
| A |
| At least 1 of the 5 sets of freeze frame data is -15% or less*3 | Sensor malfunction (value from sensor too rich) | B | |||
| All 5 sets of freeze frame data are from -15% to +15% |
| C | |||
| When idling or decelerating, engine speed rapidly decreases and engine stalls | Decreases rapidly*1 | - |
| D | |
| When accelerating or driving at constant speed, engine stalls*4 | At least one is OFF | - | - |
| E |

|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK INTAKE SYSTEM |
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] .
|
| ||||
| OK | |
| 4.CHECK PURGE VSV |
Disconnect the purge hose (on the canister side) of the purge VSV.
Start the engine.
Idle the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
Connect the connector of the purge VSV.
Connect the purge hose of the purge VSV.
|
| ||||
| OK | |
| 5.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Stop Light Switch | At least 1 of the 5 sets of freeze frame data is ON | Air suction from brake booster | A |
| All 5 sets of freeze frame data are OFF | - | B |
|
| ||||
| A | |
| 6.READ VALUE USING INTELLIGENT TESTER (SHORT FT) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the intelligent tester, read Short FT #1 of the Data List while depressing the brake pedal.
|
| ||||
| OK | |
| 7.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Calculate Load | Below 90% of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | 3.3 V or higher*2 |
| B |
| Both freeze frame data items listed above | Values are other than above | - | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Install the mass air flow meter.
|
| ||||
| A | ||
| ||
| 9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| Tester Display | Specified Condition |
| Control the Injection Volume (25%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume (-12.5%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 10.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR POWER SOURCE) |
![]() |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B7-2 (+B) - Body ground | Ignition switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B7-1 (HA1A) - B32-109 (HA1A) | Always | Below 1 Ω |
| B7-3 (A1A+) - B32-112 (A1A+) | Always | Below 1 Ω |
| B7-4 (A1A-) - B32-113 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B7-1 (HA1A) or B32-109 (HA1A) - Body ground | Always | 10 kΩ or higher |
| B7-3 (A1A+) or B32-112 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B7-4 (A1A-) or B32-113 (A1A-) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 12.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Proceed to |
| Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
|
| ||||
| A | |
| 13.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 14.INSPECT THERMOSTAT |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 15.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C or more | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temperature | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 17.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| EVAP (Purge) VSV | At least 1 of the 5 sets of freeze frame data is not 0% | Purge VSV | A |
| All 5 sets of freeze frame data are 0% | - | B |
|
| ||||
| A | |
| 18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL) |
![]() |
Disconnect the purge hose (on the canister side) of the purge VSV.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the purge VSV and check the air flow.
| Activate the VSV for Evap Control | Specified Condition |
| ON | Air flows |
| OFF | Air does not flow |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 19.INSPECT PURGE VSV |
Inspect the purge VSV .
|
| ||||
| OK | |
| 20.CHECK HARNESS AND CONNECTOR (PURGE VSV POWER SOURCE) |
![]() |
Disconnect the purge VSV connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B2-1 - Body ground | Ignition switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Purge VSV) |
|
| ||||
| OK | |
| 21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
Disconnect the purge VSV connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B2-2 - B32-49 (PRG) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B2-2 or B32-49 (PRG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 23.INSPECT FUEL PUMP |
Inspect the fuel pump .
|
| ||||
| OK | ||
| ||
| 24.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | ||
| ||
| 25.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Calculate Load | 110% or more of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | Below 3.3 V*2 |
| B |
| Both freeze frame data items listed above | Values are other than above | - | C |
|
| ||||
|
| ||||
| A | |
| 26.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
|
| ||||
| A | ||
| ||
| 27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| Tester Display | Specified Condition |
| Control the Injection Volume (25%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume (-12.5%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 28.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR POWER SOURCE) |
![]() |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B7-2 (+B) - Body ground | Ignition switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
|
| ||||
| OK | |
| 29.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B7-1 (HA1A) - B32-109 (HA1A) | Always | Below 1 Ω |
| B7-3 (A1A+) - B32-112 (A1A+) | Always | Below 1 Ω |
| B7-4 (A1A-) - B32-113 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B7-1 (HA1A) or B32-109 (HA1A) - Body ground | Always | 10 kΩ or higher |
| B7-3 (A1A+) or B32-112 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B7-4 (A1A-) or B32-113 (A1A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 30.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Proceed to |
| Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
|
| ||||
| A | |
| 31.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data.

| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 32.INSPECT THERMOSTAT |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 33.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temperature | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 35.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
| Total of ISC Learning Value and ISC Feedback Value | Below 80% of the current value of the vehicle*1 | Throttle body with motor assembly | A |
| 120% or more of the current value of the vehicle*2 | B | ||
| From 80 to 120% of the current value of the vehicle | - | C |
|
| ||||
|
| ||||
| A | |
| 36.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY |
Check for foreign matter and signs that the throttle body with motor assembly was stuck, and also check that the valve and shaft move smoothly during operation.
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 37.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY |
Check if carbon is in the airflow passage of the throttle body.
| Result | Proceed to |
| Carbon in passage | A |
| No carbon in passage | B |
|
| ||||
| A | ||
| ||
| 38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT SYSTEM) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).
Check the engine speed while operating the camshaft timing oil control valve using the tester.
| Tester Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Soon after OCV switched from OFF to ON, engine idles roughly or stalls |
|
| ||||
| OK | |
| 39.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |
| IGN Advance | Knock Correct Learn Value | ||
| Differs from the current value of the vehicle by 10° or more | Less than 3° |
| A |
| 3° or more | - | B | |
| Differs from the current value of the vehicle by less than 10° | - | - | |
|
| ||||
| A | |
| 40.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
|
| ||||
| OK | |
| 41.INSPECT MASS AIR FLOW METER |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Check MAF in the Data List during idling.
|
| ||||
| OK | ||
| ||
| 42.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | B16-1 - Ground | Ignition switch on (IG) | 11 to 14 V |
| No. 2 | B15-1 - Ground | Ignition switch on (IG) | 11 to 14 V |
| No. 3 | B14-1 - Ground | Ignition switch on (IG) | 11 to 14 V |
| No. 4 | B13-1 - Ground | Ignition switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
|
| ||||
| OK | |
| 43.CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE) |
![]() |
Disconnect the ignition coil assembly connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B12-1 (+B) - B12-4 (GND) | Ignition switch on (IG) | 11 to 14 V |
| B11-1 (+B) - B11-4 (GND) | Ignition switch on (IG) | 11 to 14 V |
| B10-1 (+B) - B10-4 (GND) | Ignition switch on (IG) | 11 to 14 V |
| B9-1 (+B) - B9-4 (GND) | Ignition switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Ignition Coil Assembly) |
|
| ||||
| OK | |
| 44.CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Idle Spark Advn Ctrl (#1 to #4) | At least one cylinder shows a value of 4° or more |
| A |
| All cylinders show a value of less than 4° | - | B |
|
| ||||
| A | |
| 45.CHECK FREEZE FRAME DATA |
Change the location of the ignition coil for the cylinder whose Idle Spark Advn Ctrl (#1 to #4) was 4° or more in step 44.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Enter the following menus: Powertrain / Engine and ECT / Data List / Idle Spark Advn Ctrl (#1 to #4).
| Result | Proceed to |
| Same as result in step 44 | A |
| Different from result in step 44 | B |
|
| ||||
| B | |
| 46.CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | ||
| A/C Signal | Air Conditioner FB Val | Power Steering Signal | ||
| A/C Signal display changes from OFF to ON | Value displayed for Air Conditioner FB Val increases | Does not change from OFF | A/C system | A |
| Changes from OFF to ON | Power steering system | B | ||
| A/C Signal display does not change from OFF | Value displayed for Air Conditioner FB Val does not increase | Changes from OFF to ON | ||
| Does not change from OFF | - | |||
|
| ||||
| B | |
| 47.CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |||
| Electrical Load Signal | Electric Load Feedback Val | Difference between Engine Speed and Turbine Speed | Vehicle Speed | ||
| Electrical Load Signal display changes from OFF to ON*1, or Value displayed for Electric Load Feedback Val increases*1 | Value displayed for Electric Load Val changes | - | - | Electrical load signal circuit | A |
| Value displayed for Electric Load Val does not change | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | A/T system | B | |
| 30 km/h or more | - | C | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | C | ||
| Electrical Load Signal display does not change from OFF, or Value displayed for Electric Load Feedback Val does not increase | - | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | A/T system | B |
| 30 km/h or more | - | C | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | C | ||
|
| ||||
|
| ||||
| A | ||
| ||
| 48.CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |
| P Position or N Position | Park/Neutral Position Switch | ||
| P and N position are both OFF in at least one data set | In D or R, NSW is ON | Park/neutral position switch | A |
| In D or R, NSW is OFF | A/T system | B | |
| All 5 sets of freeze frame data are ON | - | - | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 49.CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Throttle Sensor Position, Calculate Load | Calculate Load decreases while Throttle Sensor Position increases | Mass air flow meter | A |
| Calculate Load does not decrease while Throttle Sensor Position increases | - | B |
|
| ||||
| A | |
| 50.CHECK MASS AIR FLOW METER |
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Install the mass air flow meter.
|
| ||||
| A | ||
| ||
| 51.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | B16-1 - Ground | Ignition switch on (IG) | 11 to 14 V |
| No. 2 | B15-1 - Ground | Ignition switch on (IG) | 11 to 14 V |
| No. 3 | B14-1 - Ground | Ignition switch on (IG) | 11 to 14 V |
| No. 4 | B13-1 - Ground | Ignition switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
|
| ||||
| OK | |
| 52.CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE) |
![]() |
Disconnect the ignition coil assembly connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B12-1 (+B) - B12-4 (GND) | Ignition switch on (IG) | 11 to 14 V |
| B11-1 (+B) - B11-4 (GND) | Ignition switch on (IG) | 11 to 14 V |
| B10-1 (+B) - B10-4 (GND) | Ignition switch on (IG) | 11 to 14 V |
| B9-1 (+B) - B9-4 (GND) | Ignition switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Ignition Coil Assembly) |
|
| ||||
| OK | |
| 53.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 54.INSPECT FUEL PUMP |
Inspect the fuel pump .
|
| ||||
| OK | ||
| ||
| 55.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | ||
| ||
| 56.REPLACE MALFUNCTIONING PARTS |
If the malfunction could not be identified in steps 3 to 24, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Part to Replace |
| Step 6 | Brake booster |
| Step 8 | Mass air flow meter |
| Step 9 | Air fuel ratio sensor |
| Step 16 | Engine coolant temperature sensor |
| Step 18 | Purge VSV |
| Step 24 | Fuel pump |
If the malfunction could not be identified in steps 25 to 34, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Part to Replace |
| Step 26 | Mass air flow meter |
| Step 27 | Air fuel ratio sensor |
| Step 34 | Engine coolant temperature sensor |
If the malfunction could not be identified in steps 35 to 41, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Part to Replace |
| Step 36, 37 | Throttle body with motor assembly |
| Step 39 | Knock sensor |
If the malfunction could not be identified in steps 42 to 48, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection |
| Step 46 | A/C system inspection and repair Power steering system inspection and repair |
| Step 47 | A/T system inspection and repair Electrical load system inspection and repair |
| Step 48 | Park/neutral position switch inspection and repair A/T system inspection and repair |
If the malfunction could not be identified in steps 49 to 55, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Part to Replace |
| Step 50 | Mass air flow meter |
| NEXT | |
| 57.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Clear the DTCs (Click here).
| NEXT | |
| 58.PERFORM CONFIRMATION DRIVING PATTERN |
Check if engine stall symptoms are present.
|
| ||||
| OK | ||
| ||