Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

DTC    C0273/13    Open in ABS Motor Relay Circuit

DTC    C0274/14    Short to B+ in ABS Motor Relay Circuit

for Preparation Click here


DESCRIPTION

The ABS motor relay supplies the power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay ON and operates the ABS pump motor.

DTC No.
DTC Detection Condition
Trouble Area
C0273/13
When either condition below is met:
  1. All of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage between 9.5 V and 18.5 V.
    2. During initial check or ABS operation.
    3. Relay contact open when relay on.
  2. Both of following conditions continue for 0.12 seconds or more.
    1. IG1 terminal voltage is 9.5 V or less.
    2. Relay contact remains open when relay on.
  1. ABS1 H-fuse
  2. Harness or connector (+BM circuit)
  3. Brake actuator (Skid control ECU)
C0274/14
When motor relay off, motor relay remains closed for 4 seconds or more.
  1. ABS1 H-fuse
  2. Harness or connector (+BM circuit)
  3. Brake actuator (Skid control ECU)

HINT:
C0273/13 and C0274/14: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 6 km/h (4 mph).


WIRING DIAGRAM

Refer to DTC C0226/21, C0236/22, C0246/23, C0256/24 .

INSPECTION PROCEDURE

1.INSPECT FUSE (ABS1)
  1. Remove the ABS1 H-fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)


    C117862E06
  1. Disconnect the A27 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A27-23 (+BM) - Body ground
    11 to 14 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A27-2 (GND1) - Body ground
    Below 1 Ω
    A27-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)
  1. Select the Active Test, generate a control command, and then check that the motor relay operates.

    Skid control ECU 
    Tester Display
    Test Parts
    Control Range
    Diagnostic Note
    Motor Relay
    Turns ABS motor relay
    ON or OFF
    Operating sound of motor can be heard

    OK:
    Operation sound of the ABS motor is heard.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at 6 km/h (4 mph) or more to activate the initial check.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)