DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |


| DTC No. | DTC Detection Condition | Trouble Area |
| P2237 | An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic). |
|
| P2238 | One of the following conditions is met (2 trip detection logic):
|
|
| P2239 | The A1A+ voltage is higher than 4.5 V (2 trip detection logic). |
|
| P2252 | The A1A- voltage is 0.5 V or less (2 trip detection logic). |
|
| P2253 | The A1A- voltage is higher than 4.5 V (2 trip detection logic). |
|
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1 S1 (A/F) | +25% | Rich | Below 3.1 V |
| AFS Voltage B1 S1 (A/F) | -12.5% | Lean | Higher than 3.4 V |
| O2S B1 S2 (HO2) | +25% | Rich | Higher than 0.55 V |
| O2S B1 S2 (HO2) | -12.5% | Lean | Below 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
![]() |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B113-3 (A1A+) - B32-103 (A1A+) | Always | Below 1 Ω |
| B113-4 (A1A-) - B32-126 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B113-3 (A1A+) or B32-103 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B113-4 (A1A-) or B32-126 (A1A-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
Reconnect the air fuel ratio sensor connector.

|
| ||||
| OK | |
| 2.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 3.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Switch the ECM from normal mode to check mode (Click here).
Drive the vehicle according to the Confirmation Driving Pattern .
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs (pending DTCs).
| Result | Proceed to |
| DTC is not output | A |
| DTC P2237, P2238, P2239, P2252 or P2253 is output | B |
|
| ||||
| A | ||
| ||