Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0660    Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)

for Preparation Click here


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

A172378E01


Text in Illustration 
*1
Intake Air Control Valve Open
*2
Intake Air Control Valve Closed

DTC No.
DTC Detection Condition
Trouble Area
P0660
The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
  1. The voltage of terminal ACIS of the ECM is low when the VSV is off.
  2. The engine has been started.
  1. Open or short in VSV for ACIS circuit
  2. Intake manifold (intake air control valve)
  3. ECM

WIRING DIAGRAM


A200657E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE VSV FOR ACIS)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Active the VSV for Intake Control.

  1. Check if an operating noise can be heard when operating the air intake control valve using the intelligent tester.

    OK:
    Operating noise can be heard.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK VSV FOR ACIS
  1. Check the VSV for ACIS (Click here).



NG
REPLACE VSV FOR ACIS
OK


3.CHECK VSV FOR ACIS (POWER SOURCE)


    A107917E57
  1. Disconnect the VSV for ACIS connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B125-1 - B125-2
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to VSV for ACIS)



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM)


    A206535E02
  1. Disconnect the VSV for ACIS connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B125-1 - B32-38 (ACIS)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B125-1 or B32-38 (ACIS) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to VSV for ACIS)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the VSV for ACIS connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VSV FOR ACIS - ECM)
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - INTEGRATION RELAY)


    A210498E02
  1. Disconnect the VSV for ACIS connector.

  1. Remove the integration relay (EFI MAIN relay) from the engine room No. 1 relay block and disconnect the integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B125-2 - 1A-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B125-2 or 1A-4 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to VSV for ACIS)
    *2
    Front view of wire harness connector
    (to Integration Relay)
    *3
    Engine Room No. 1 Relay Block

  1. Reconnect the integration relay connector.

  1. Reinstall the integration relay.

  1. Reconnect the VSV for ACIS connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VSV FOR ACIS - INTEGRATION RELAY)
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)