Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to terminal IGSW of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil, closing the contacts of the integration relay (EFI MAIN relay) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM


A210082E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    A152957E68
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B32-105 (E1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)
OK


2.INSPECT ECM (IGSW VOLTAGE)


    A148741E33
  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A12-27 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


3.INSPECT INTEGRATION NO.1 RELAY (EFI MAIN RELAY)


    A210314E01
  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Disconnect the integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - 1A-4
    Battery voltage not applied to terminal 1A-2 and 1A-3
    10 kΩ or higher
    Battery voltage applied to terminal 1A-2 and 1A-3
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Integration Relay)
    *2
    Engine Room No. 1 Relay Block

  1. Reconnect the integration relay connector.

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION NO.1 RELAY (EFI MAIN RELAY)
OK


4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [EFI MAIN RELAY] - ECM)


    A210319E01
  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Disconnect the integration relay connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1A-4 - A12-2 (+B)
    Always
    Below 1 Ω
    1A-4 - A12-1 (+B2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1A-4 or A12-2 (+B) - Body ground
    Always
    10 kΩ or higher
    1A-4 or A12-1 (+B2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Engine Room No. 1 Relay Block
    *3
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the integration relay connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [EFI MAIN RELAY] - ECM)
OK


5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [EFI MAIN RELAY] - BATTERY)


    A210315E01
  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Disconnect the integration relay connector.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1C-1 - Positive battery terminal
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1C-1 or Positive battery terminal - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Engine Room No. 1 Relay Block

  1. Reconnect the integration relay connector.

  1. Reinstall the integration relay.

  1. Reconnect the cable to the positive (+) battery terminal.

  1. Reconnect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [EFI MAIN RELAY] - BATTERY)
OK


6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [EFI MAIN RELAY] - BODY GROUND)


    A210316E01
  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Disconnect the integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1A-3 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Engine Room No. 1 Relay Block

  1. Reconnect the integration relay connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [EFI MAIN RELAY] - BODY GROUND)
OK


7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [EFI MAIN RELAY] - ECM)


    A210319E02
  1. Disconnect the ECM connector.

  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Disconnect the integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1A-2 - A12-44 (MREL)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1A-2 or A12-44 (MREL) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Engine Room No. 1 Relay Block
    *3
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the integration relay connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [EFI MAIN RELAY] - ECM)
OK

REPLACE ECM (Click here)  

8.INSPECT IGNITION RELAY NO. 2 (IG2)
  1. Remove the ignition relay No. 2 (IG2) from the engine room No. 1 relay block.

  1. Inspect the ignition relay No. 2 .

  1. Reinstall the ignition relay No. 2 (IG2).



NG
REPLACE IGNITION RELAY NO. 2 (IG2)
OK


9.CHECK HARNESS AND CONNECTOR (IGNITION RELAY NO. 2 (IG2) - ECM)


    A128628E05
  1. Disconnect the ECM connector.

  1. Remove the ignition relay No. 2 (IG2) from the engine room No. 1 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 5 - A12-27 (IGSW)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 5 or A12-27 (IGSW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Engine Room No. 1 Relay Block
    *2
    IG2
    *3
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reinstall the ignition relay No. 2 (IG2).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION RELAY NO. 2 (IG2) - ECM)
OK


10.CHECK HARNESS AND CONNECTOR (IGNITION RELAY NO. 2 (IG2) - BATTERY)


    A210083E01
  1. Remove the ignition relay No. 2 (IG2) from the engine room No. 1 relay block.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 3 - Positive battery terminal
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 3 or positive battery terminal - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Engine Room No. 1 Relay Block
    *2
    IG2

  1. Reinstall the ignition relay No. 2 (IG2).

  1. Reconnect the cable to the positive (+) battery terminal.

  1. Reconnect the cable to the negative (-) battery terminal.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION RELAY NO. 2 (IG2) - BATTERY)
OK


11.CHECK HARNESS AND CONNECTOR (IGNITION RELAY NO. 2 (IG2) - BODY GROUND)


    A210083E01
  1. Remove the ignition relay No. 2 (IG2) from the engine room No. 1 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 2 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Engine Room No. 1 Relay Block
    *2
    IG2

  1. Reinstall the ignition relay No. 2 (IG2).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION RELAY NO. 2 (IG2) - BODY GROUND)
OK


12.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
  1. Check if the vehicle is equipped with an entry and start system.
    Result 
    Result
    Proceed to
    w/o Entry and Start System
    A
    w/ Entry and Start System
    B



B
Go to step 15
A


13.CHECK HARNESS AND CONNECTOR (IGNITION RELAY NO. 2 (IG2) - IGNITION SWITCH)


    A128631E05
  1. Disconnect the ignition switch connector.

  1. Remove the ignition relay No. 2 (IG2) from the engine room No. 1 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 1 - E5-6 (IG2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 1 or E5-6 (IG2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Engine Room No. 1 Relay Block
    *2
    IG2
    *3
    Front view of wire harness connector
    (to Ignition Switch)

  1. Reconnect the ignition switch connector.

  1. Reinstall the ignition relay No. 2 (IG2).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION RELAY NO. 2 (IG2) - IGNITION SWITCH)
OK


14.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY) 

15.CHECK HARNESS AND CONNECTOR (IGNITION RELAY NO. 2 (IG2) - MAIN BODY ECU)


    A128629E05
  1. Disconnect the main body ECU connector.

  1. Remove the ignition relay No. 2 (IG2) from the engine room No. 1 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 1 - E19-5 (IG2D)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Ignition relay No. 2 (IG2) terminal 1 or E19-5 (IG2D) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Engine Room No. 1 Relay Block
    *2
    IG2
    *3
    Rear view of wire harness connector
    (to Main Body ECU)

  1. Reconnect the main body ECU connector.

  1. Reinstall the ignition relay No. 2 (IG2).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION RELAY NO. 2 (IG2) - MAIN BODY ECU)
OK

CHECK ENTRY AND START SYSTEM (Click here)