Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0500    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

The vehicle speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signals.

HINT:
Each ECU controls its respective system based on this pulse signal, and if a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems that use the vehicle speed signal to perform control will not operate normally.


A208622E03


DTC No.
DTC Detection Condition
Trouble Area
P0500
While the vehicle is being driven, no vehicle speed sensor signal is sent to the ECM.
(1 trip detection logic: for CVT)
(2 trip detection logic: for manual transaxle)
  1. Open or short in speed signal circuit
  2. Combination meter
  3. Skid control ECU
  4. Vehicle speed sensor
  5. Main body ECU
  6. Radio receiver assembly
  7. Navigation receiver assembly
  8. Tire pressure warning ECU
  9. Auto wiper relay
  10. ECM

WIRING DIAGRAM


A210499E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speeds displayed on tester and speedometer display are equal.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK COMBINATION METER SYSTEM
  1. The circuits that send vehicle speed signals to this system are inspected in the meter system (Click here).

  1. During the inspection in the meter section, if there is an instruction to proceed to the next suspected area, proceed to the next step.


NEXT


3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)


    A127855E48
  1. Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E22-39 (+S) - A12-38 (SPD)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the combination meter connector.



NG
Go to step 4
OK

REPLACE ECM (Click here)  

4.CHECK HARNESS AND CONNECTOR (ECM - NO. 3 JUNCTION BLOCK)


  1. Disconnect the ECM connector.


    A210500E01

  1. Disconnect the No. 3 junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    3A-78 - A12-38 (SPD)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    3A-56 - A12-38 (SPD)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 3 Junction Block
    *2
    Front view of wire harness connector
    (to No. 3 Junction Block)
    *3
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the No. 3 junction block connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - NO. 3 JUNCTION BLOCK)
OK

REPAIR OR REPLACE NO. 3 JUNCTION BLOCK