The Tumble Control Valve (TCV) is built into the intake manifold. The intake air control valve actuator (for tumble control valve) is composed of a position sensor and a DC motor. The DC motor opens and closes the tumble control valve in response to signals from the ECM. The position sensor detects the opening angle of the tumble control valve.
When the tumble control valve is closed, the intake air tumble flow intensifies and negative pressure is generated between the tumble control valve and intake valve which atomizes the fuel. Combustion is enhanced and exhaust gas emissions are reduced at low temperatures.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P2004 | Intake Manifold Runner Control Stuck Open (Bank 1) | The tumble control valve opening angle is 17 deg. or more after requesting the tumble control valve to fully close (2 trip detection logic). | ·
Open or short in intake air control valve actuator (for tumble control valve) circuit ·
Intake air control valve actuator (for tumble control valve) ·
Intake manifold ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
| P2006 | Intake Manifold Runner Control Stuck Closed (Bank 1) | The tumble control valve opening angle is less than 35 deg. after requesting the tumble control valve to fully open (2 trip detection logic). | ·
Open or short in intake air control valve actuator (for tumble control valve) circuit ·
Intake air control valve actuator (for tumble control valve) ·
Intake manifold ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
When P2004 and/or P2006 is output, use the Techstream to confirm Intake Air Control Position while performing Control the IAC Duty Ratio of the Active Test.
| Control the IAC Duty Ratio Operation | Intake Air Control Position |
|---|---|
| 100% | Approximately 70 deg. |
| 0% | Approximately 70 deg. |
| -100% | Approximately 2 deg. |
When the ECM has requested a tumble control valve close operation but the actual tumble control valve opening angle is 17 deg. or more for 10 seconds, DTC P2004 is stored. When the ECM has requested a tumble control valve open operation but the actual tumble control valve opening angle is less than 35 deg. for 10 seconds, DTC P2006 is stored.
| Related DTCs | P2004: Tumble Control Valve (TCV) stuck open
P2006: Tumble Control Valve (TCV) stuck closed |
| Required Sensors/Components (Main) | Tumble control valve |
| Required Sensors/Components (Related) | Intake air temperature sensor
Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Approximately 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Engine coolant temperature | -10°C (14°F) or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Ignition switch | ON |
| Battery voltage | 8 V or higher |
| Control valve angle when commanded closed | 17 deg. or more |
| Control valve angle when commanded open | Less than 35 deg. |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check for DTC P2004 at an engine coolant temperature of 30°C (86°F) or less.
Check for DTC P2006 at an engine coolant temperature of 80°C (176°F) or higher.
Turn the ignition switch off.
Turn the ignition switch to ON, wait approximately 10 seconds, and then turn the ignition switch off. Repeat this procedure 3 times [B].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2004 or P2006.
Check the DTC judgment result.
| Techstream Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2004 or P2006 is output | A |
| DTC P2004 or P2006 and other DTCs are output | B |
If any DTCs other than P2004 or P2006 are output, troubleshoot those DTCs first.
A
B
Inspect the intake air control valve actuator (for tumble control valve).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>REMOVAL
Inspect the intake manifold for the tumble control valve operation.
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the intake air control valve actuator connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X2-4 (M-) - B77-21 (IA1-) | Always | Below 1 Ω |
| X2-5 (M+) - B77-22 (IA1+) | Always | Below 1 Ω |
| X2-4 (M-) or B77-21 (IA1-) - Body ground | Always | 10 kΩ or higher |
| X2-5 (M+) or B77-22 (IA1+) - body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2004 or P2006 is output | A |
| DTC is not output | B |
A
B