Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

w/ Fuel Pump Control ECU Assembly:

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump ECU adjust the fuel pump operation speed.


w/o Fuel Pump Control ECU Assembly:

When the engine is cranked, the ST (starter) relay drive signal output from the ignition switch assembly*1 or certification ECU (smart key ECU assembly)*2 is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.

*1: w/o Smart Key System

*2: w/ Smart Key System


WIRING DIAGRAM

A299785
5.917,0.542 6.333,0.708 0.417,0.167 10 false IG2D 5.75,0.438 5.917,0.604 0.167,0.167 10 false 9 5.5,1 5.833,1.167 0.333,0.167 10 false G82 5.5,1.167 7.083,1.583 1.583,0.417 10 false Certification ECU (Smart Key ECU Assembly)*1 5.917,3.458 6.417,3.625 0.5,0.167 10 false MREL 5.667,3.365 5.917,3.531 0.25,0.167 10 false 46 5.5,5.333 5.833,5.5 0.333,0.167 10 false IGN 4.719,3.969 5.385,4.135 0.667,0.167 10 false EFI NO. 2 5.917,6.823 6.167,6.99 0.25,0.167 10 false FC 5.667,6.823 5.917,6.99 0.25,0.167 10 false 21 6.25,8 6.583,8.167 0.333,0.167 10 false A62 6.25,8.167 6.667,8.333 0.417,0.167 10 false ECM 3.25,0.438 3.417,0.604 0.167,0.167 10 false 3 2.917,0.667 3.25,0.833 0.333,0.167 10 false IG2 2.25,0.667 2.667,0.833 0.417,0.167 10 false AM2 1.917,0.75 2.167,0.917 0.25,0.167 10 false G4 1.917,0.917 3.667,1.083 1.75,0.167 10 false Ignition Switch Assembly*2 2.083,0.438 2.25,0.604 0.167,0.167 10 false 4 0.927,0.688 1.26,0.854 0.333,0.167 10 false AM2 0.958,1.802 1.292,1.969 0.333,0.167 10 false IG2 0.719,7.948 1.219,8.198 0.5,0.25 10 false Battery 1.917,7.5 2.083,7.667 0.167,0.167 10 false B 1.927,8.052 2.094,8.219 0.167,0.167 10 false E 2.458,7.667 2.708,7.833 0.25,0.167 10 false V1 2.458,7.833 3.208,8.021 0.75,0.188 10 false Fuel Pump 1.938,8.25 2.104,8.417 0.167,0.167 10 false 5 1.938,7.323 2.104,7.49 0.167,0.167 10 false 4 3.01,5.104 4.094,5.271 1.083,0.167 10 false EFI-MAIN NO. 2 3.281,6.615 3.781,6.781 0.5,0.167 10 false C/OPN 3.01,3.792 4.094,3.958 1.083,0.167 10 false EFI-MAIN NO. 1 3.375,2.333 3.708,2.5 0.333,0.167 10 false IG2 3.385,8.167 5.333,8.417 1.948,0.25 10 false *2: w/o Smart Key System 3.385,7.667 5.333,7.917 1.948,0.25 10 false *1: w/ Smart Key System 3.083,1.552 3.25,1.719 0.167,0.167 10 false 3 3.833,1.552 4,1.719 0.167,0.167 10 false 5 3.833,1.885 4,2.052 0.167,0.167 10 false 1 3.083,1.885 3.25,2.052 0.167,0.167 10 false 2 0.583,3.25 1.667,3.417 1.083,0.167 10 false EFI-MAIN NO. 1 0.583,4.958 1.667,5.125 1.083,0.167 10 false EFI-MAIN NO. 2 3.083,2.99 3.25,3.156 0.167,0.167 10 false 5 3.833,2.99 4,3.156 0.167,0.167 10 false 3 3.083,3.365 3.25,3.531 0.167,0.167 10 false 2 3.833,3.365 4,3.531 0.167,0.167 10 false 1 3.823,4.313 3.99,4.479 0.167,0.167 10 false 1 3.833,6.188 4,6.354 0.167,0.167 10 false 1 3.833,4.677 4,4.844 0.167,0.167 10 false 3 3.083,5.76 3.25,5.927 0.167,0.167 10 false 3 3.083,4.313 3.25,4.479 0.167,0.167 10 false 2 3.083,4.677 3.25,4.844 0.167,0.167 10 false 5 3.833,5.76 4,5.927 0.167,0.167 10 false 5 3.083,6.188 3.25,6.354 0.167,0.167 10 false 2 0.583,6.167 1.167,6.333 0.583,0.167 10 false FL MAIN 6.5,6.25 6.75,6.417 0.25,0.167 10 false Tr1 0.115,0.115 0.844,0.344 0.729,0.229 12 false for AWD:

A299784
6.083,0.563 6.583,0.729 0.5,0.167 10 false MREL 6.083,1.479 6.417,1.646 0.333,0.167 10 false FPC 5.833,1.479 6.083,1.646 0.25,0.167 10 false 21 5.833,0.458 6.083,0.625 0.25,0.167 10 false 46 5.083,1.479 5.25,1.646 0.167,0.167 10 false 2 4.667,1.583 5,1.75 0.333,0.167 10 false FPC 5.083,2.083 5.667,2.25 0.583,0.167 10 false N19 5.083,2.25 5.917,2.583 0.833,0.333 10 false Fuel Pump Control ECU 4.667,2.99 5,3.156 0.333,0.167 10 false FP- 4.042,2.99 4.292,3.156 0.25,0.167 10 false FP 4,1.583 4.167,1.75 0.167,0.167 10 false E 4,1.031 4.25,1.198 0.25,0.167 10 false +B 3.75,0.938 3.917,1.104 0.167,0.167 10 false 1 3.75,1.479 3.917,1.646 0.167,0.167 10 false 4 4,3.167 4.167,3.333 0.167,0.167 10 false 6 4.667,3.167 4.833,3.333 0.167,0.167 10 false 5 4.833,4.042 5,4.208 0.167,0.167 10 false 5 4.167,4.042 4.333,4.208 0.167,0.167 10 false 4 4,4.25 4.167,4.417 0.167,0.167 10 false B 4.646,4.25 4.813,4.417 0.167,0.167 10 false E 4.083,4.833 4.333,5 0.25,0.167 10 false V1 4.083,5 4.833,5.167 0.75,0.167 10 false Fuel Pump 0.917,1.167 1.583,1.333 0.667,0.167 10 false EFI NO. 2 1.083,1.885 1.5,2.385 0.417,0.5 10 false EFI-MAIN NO. 1 2.333,1.885 2.75,2.385 0.417,0.5 10 false EFI-MAIN NO. 2 0.833,4.667 1.333,4.917 0.5,0.25 10 false Battery 2.167,1.667 2.333,1.833 0.167,0.167 10 false 3 6.333,3.583 6.667,3.75 0.333,0.167 10 false A62 6.333,3.75 6.75,3.917 0.417,0.167 10 false ECM 0.667,2.792 1.75,2.958 1.083,0.167 10 false EFI-MAIN NO. 1 2.198,2.792 3.281,2.958 1.083,0.167 10 false EFI-MAIN NO. 2 1.667,1.667 1.833,1.833 0.167,0.167 10 false 1 0.917,1.667 1.083,1.833 0.167,0.167 10 false 1 0.417,1.667 0.583,1.833 0.167,0.167 10 false 3 1.667,2.438 1.833,2.604 0.167,0.167 10 false 2 2.167,2.438 2.333,2.604 0.167,0.167 10 false 5 0.917,2.438 1.083,2.604 0.167,0.167 10 false 2 0.417,2.438 0.583,2.604 0.167,0.167 10 false 5 0.677,3.729 1.26,3.896 0.583,0.167 10 false FL MAIN 6.667,1.583 6.917,1.75 0.25,0.167 10 false Tr1 0.094,0.083 0.802,0.333 0.708,0.25 12 false for 2WD:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

·

w/ Fuel Pump Control ECU Assembly


Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230
·

w/o Fuel Pump Control ECU Assembly


Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the Techstream.

Result:
Result Proceed to
Fuel pump operating sound does not occur
(w/ fuel pump control ECU assembly)
A
Fuel pump operating sound does not occur
(w/o fuel pump control ECU assembly)
B
Fuel pump operating sound occurs
(w/ fuel pump control ECU assembly)
C
Fuel pump operating sound occurs
(w/o fuel pump control ECU assembly)
D




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)

B

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)

C

18.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY)

D

23.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)
a.
A290250
0.458,1.115 0.813,1.333 0.354,0.219 1.063,1.823 1.25,1.521 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.521,1.146 0.979,1.344 0.458,0.198 10 false N19 0.854,1.76 1.167,1.958 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Fuel Pump Control ECU Assembly)


Disconnect the fuel pump control ECU Assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N19-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-4 (B) - N19-6 (FP) Always Below 1 Ω
V1-5 (E) - N19-5 (FP-) Always Below 1 Ω
V1-4 (B) or N19-6 (FP) - Body ground Always 10 kΩ or higher
V1-5 (E) or N19-5 (FP-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL PUMP
a.

Inspect fuel pump.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-2 (FPC) - A62-21 (FPC) Always Below 1 Ω
N19-2 (FPC) or A62-21 (FPC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
a.

Replace the fuel pump control ECU assembly.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay) - N19-1 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 2 relay) or N19-1 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)
a.
A298899
0.063,0.063 0.375,0.219 0.313,0.156 10 *1 2.042,1.115 2.354,1.271 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 C/OPN Relay


Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (C/OPN relay) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.INSPECT C/OPN RELAY

NG

17.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - IG2 RELAY)
11.INSPECT C/OPN RELAY

Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)

NG

REPLACE C/OPN RELAY

12.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (C/OPN relay) - A62-21 (FC) Always Below 1 Ω
2 (C/OPN relay) or A62-21 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (C/OPN relay) - V1-4 (B) Always Below 1 Ω
3 (C/OPN relay) or V1-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT FUEL PUMP
a.

Inspect fuel pump.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 2 RELAY)

NG

16.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 2 RELAY)
a.

Remove the C/OPN relay and EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (C/OPN relay) - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
5 (C/OPN relay) or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - IG2 RELAY)
a.

Remove the C/OPN relay and IG2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (C/OPN relay) - 5 (IG2 relay) Always Below 1 Ω
1 (C/OPN relay) or 5 (IG2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP DUTY)
a.

Remove the fuel suction with pump and gauge tube assembly.


b.

Clean the fuel suction with pump and gauge tube assembly to completely remove any remaining fuel.


c.

Remove the fuel pump.


d.

Connect the fuel pump and fuel suction with pump and gauge tube assembly connector.

NOTICE:

Confirm that no fuel remains inside or on the outside of the fuel pump.



e.

Connect the Techstream to the DLC3.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump Duty
50004 234 229

i.
A285444
1.031,1.719 1.552,0.833 false 2.469,1.75 1.865,0.833 false 0.281,0.219 0.646,0.573 0.365,0.354 10 *a 0.958,1.771 1.323,2.125 0.365,0.354 10 1 2.479,1.771 2.844,2.125 0.365,0.354 10 2
*a Component with harness connected
(Fuel Pump)


Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Techstream Operation Specified Condition
1 - 2 Fuel pump control duty: 25% 3.4 to 4.1 V
Fuel pump control duty: 80% 10.0 to 12.5 V



j.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

k.

Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Techstream Operation Specified Condition
1 - 2 ON (Fuel pump control duty: 90%) 10.2 to 14.0 V


HINT:
·

Be sure to measure the voltage with all the connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

22.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
19.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-2 (FPC) - A62-21 (FPC) Always Below 1 Ω
N19-2 (FPC) or A62-21 (FPC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.REPLACE FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.REPLACE FUEL PUMP
a.

Replace the fuel pump.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL PUMP>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

22.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
a.

Replace the fuel pump control ECU assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL PUMP ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
23.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Engine Started ON



Result:
Proceed to
OK
NG



OK

24.READ VALUE USING TECHSTREAM (ENGINE SPEED)

NG

24.READ VALUE USING TECHSTREAM (ENGINE SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the Techstream while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT