Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch and to terminal STA of the ECM (STA signal).

*1: w/o Smart Key System

*2: w/ Smart Key System


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

This procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH SMART KEY SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result
w/o Smart Key System
w/ Smart Key System




w/o Smart Key System

2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)

w/ Smart Key System

10.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK ST RELAY (POWER SOURCE)
3.CHECK ST RELAY (POWER SOURCE)
a.
A290310
0.104,0.083 0.417,0.24 0.313,0.156 10 *1 0.49,1.969 0.802,2.125 0.313,0.156 10 *2
*1 No. 2 Engine Room Relay Block Assembly
*2 ST Relay


Remove the ST relay from the No. 2 Engine Room Relay Block Assembly


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 2 - Body ground Engine cranking 11 to 14 V


HINT:

The engine does not crank because the relay is not installed.


Result:
Proceed to
OK
NG




OK

4.INSPECT RELAY (ST RELAY)

NG

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
4.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPLACE RELAY (ST RELAY)

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the No. 2 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Remove the ST relay from the No. 2 engine room relay block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-9 (L) - ST relay terminal 2 Always Below 1 Ω
A62-22 (STA) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ignition switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - B36-4 (B) Always Below 1 Ω
G4-2 (ST2) - B77-63 (NSW) Always Below 1 Ω
G4-2 (ST2) or B36-4 (B) or B77-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

10.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

NG

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Remove the ST relay from the No. 2 engine room relay block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-9 (L) - ST relay terminal 2 Always Below 1 Ω
A62-22 (STA) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - B36-4 (B) Always Below 1 Ω
G82-5 (STAR) - B77-63 (NSW) Always Below 1 Ω
G82-5 (STAR) or B36-4 (B) or B77-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR