Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM30B0U _53 Suspension _009252 TIRE PRESSURE MONITORING _0050645 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2141/41  Transmitter ID1 Error  C2142/42  Transmitter ID2 Error  C2143/43  Transmitter ID3 Error  C2144/44  Transmitter ID4 Error  C2145/45  Transmitter ID5 Error  


DESCRIPTION

The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressures. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured air pressure values with the air pressure threshold. When the measured air pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.

When the internal circuit of a tire pressure warning valve and transmitter is malfunctioning, one of these DTCs is output.

DTC No. Detection Item DTC Detection Condition Trouble Area
C2141/41 Transmitter ID1 Error If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will be judged as defective and a DTC will be output. This will happen in situations where the inflation pressure is outside the range 0 to 380 kPa (0 to 3.9 kgf/cm2, 0 to 55 psi), the temperature inside the tire is outside the specified range -40 to 120°C (-40 to 248°F), or an error occurs in the tire pressure warning valve and transmitter or the surrounding area.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


C2142/42 Transmitter ID2 Error If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will be judged as defective and a DTC will be output. This will happen in situations where the inflation pressure is outside the range 0 to 380 kPa (0 to 3.9 kgf/cm2, 0 to 55 psi), the temperature inside the tire is outside the specified range -40 to 120°C (-40 to 248°F), or an error occurs in the tire pressure warning valve and transmitter or the surrounding area.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


C2143/43 Transmitter ID3 Error If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will be judged as defective and a DTC will be output. This will happen in situations where the inflation pressure is outside the range 0 to 380 kPa (0 to 3.9 kgf/cm2, 0 to 55 psi), the temperature inside the tire is outside the specified range -40 to 120°C (-40 to 248°F), or an error occurs in the tire pressure warning valve and transmitter or the surrounding area.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


C2144/44 Transmitter ID4 Error If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will be judged as defective and a DTC will be output. This will happen in situations where the inflation pressure is outside the range 0 to 380 kPa (0 to 3.9 kgf/cm2, 0 to 55 psi), the temperature inside the tire is outside the specified range -40 to 120°C (-40 to 248°F), or an error occurs in the tire pressure warning valve and transmitter or the surrounding area.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver


C2145/45 Transmitter ID5 Error If an "ERROR" signal is received 3 times consecutively, the tire pressure warning valve and transmitter will be judged as defective and a DTC will be output. This will happen in situations where the inflation pressure is outside the range 0 to 380 kPa (0 to 3.9 kgf/cm2, 0 to 55 psi), the temperature inside the tire is outside the specified range -40 to 120°C (-40 to 248°F), or an error occurs in the tire pressure warning valve and transmitter or the surrounding area.
·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver



C2145/45: w/ Full Size Spare Tire


HINT:

It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.IDENTIFY TRANSMITTER CORRESPONDING TO DTC
a.

Set the tire pressure to the specified values.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Display the "ID Tire Inflation Pressure" data for each wheel using the Techstream.


h.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds. If "ID Tire Inflation Pressure" displayed on the Techstream does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" data was the cause of the output DTC.

HINT:
·

Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each tire.

·

Record which "ID Tire Inflation Pressure" data corresponds to each tire.



Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*

·

w/ Full Size Spare Tire


HINT:

*: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: w/ Full Size Spare Tire).

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121/21


Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40

i.

Check the Data List.

Result:
Result Proceed to
One of "ID Tire Inflation Pressure" data changed. Normal
"ID Tire Inflation Pressure" data did not change. Transmitter corresponding to DTC


NOTICE:
·

It may take a few minutes to display the updated tire pressure data.

·

When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.

·

Record the transmitter ID of which "ID Tire Inflation Pressure" data corresponds to each tire.




j.

When the "ID Tire Inflation Pressure" data has changed, repeat this procedure to identify the tire pressure warning valve and transmitter that corresponds to the DTC.


k.

When all of the "ID Tire Inflation Pressure" data has changed, identify the malfunctioning tire pressure warning valve and transmitter using the recorded ID numbers and output DTCs.


Result:
Proceed to
NEXT



NEXT

2.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
2.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a.

Replace the identified tire pressure warning valve and transmitter with a new one.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING VALVE>REMOVAL

HINT:
·

Before installing a new tire pressure warning valve and transmitter, read and write down its transmitter ID.

·

The IDs for the tire pressure warning valve and transmitters which are not replaced should be checked using the Techstream and recorded.




Result:
Proceed to
NEXT



NEXT

3.REGISTRATION OF TRANSMITTER ID
3.REGISTRATION OF TRANSMITTER ID
a.

Register the transmitter ID for all wheels.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

4.PERFORM INITIALIZATION
4.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

5.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
5.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 388.72kPa (3.9 kgf/cm2, 56 psi)
Actual tire inflation pressure
·

If N/A is displayed, data has not been received.*

·

w/ Full Size Spare Tire


HINT:
·

*: It may take a few minutes until the values are displayed.

·

When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.



Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40
Result:
Proceed to
Tire pressure values are not displayed.
All tire pressure readings are equal to specified values.




Tire pressure values are not displayed.

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

All tire pressure readings are equal to specified values.

END