Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CAMSHAFT
RM30B0U _51 Engine / Hybrid System _009173 2AR-FE ENGINE MECHANICAL _0050871 CAMSHAFT A

2AR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR ENGINE UNDER COVER RH

Hide 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 6.REMOVE AIR CLEANER CASE

Hide 7.DISCONNECT RADIATOR RESERVOIR ASSEMBLY

Hide 8.DISCONNECT ENGINE WIRE

a.
A296282

Disconnect the connectors and clamps, remove the bolts and nuts and disconnect the engine wire from the engine.


Hide 11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A245326
1.01,1.115 1.896,0.26 1.896,0.26 2.969,1.135 true 1.042,1.323 1.865,1.833 1.865,1.833 3,1.344 true 1.635,3.198 2.438,3.708 2.438,3.708 2.813,3.708 true 1.802,0.042 1.99,0.229 0.188,0.188 10 *1 1.771,1.854 1.958,2.042 0.188,0.188 10 *2 2.865,3.604 3.052,3.792 0.188,0.188 10 *3
*1 Paint Mark
*2 Matchmark
*3 Timing Notch (Groove)


Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover are aligned.


b.

Check that each matchmark of the camshaft timing gear and camshaft timing exhaust gear are aligned with each matchmark located as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.


c.

Place paint marks on the chain in alignment with the timing marks on the camshaft timing gear and camshaft timing exhaust gear.


Hide 13.REMOVE TIMING CHAIN COVER PLATE

a.
A250986

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 14.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A245327
1.958,0.281 2.229,0.458 0.271,0.177 10 *a
*a Approximately 10°


Turn the crankshaft approximately 10° clockwise.


b.
A249931
2.01,0.302 2.26,0.448 0.25,0.146 10 *a
*a Approximately 10°


Turn the crankshaft approximately 10° counterclockwise.


c.
A249932
1.927,2.031 1.802,2.031 1.802,2.031 1.635,1.708 false 2,1.948 2.229,2.094 0.229,0.146 10 *1
*1 Pin


Align the holes of the stopper plate and tensioner, and insert a pin into the stopper plate hole to lock the tensioner.


d.
A245327
2,0.26 2.271,0.438 0.271,0.177 10 *a
*a Approximately 10°


Turn the crankshaft approximately 10° clockwise.


e.
A249933

Remove the 2 bolts, No. 1 chain tensioner and gasket.

NOTICE:

Make sure not to drop the gasket inside the timing chain cover.



f.
A249931
2.01,0.292 2.26,0.438 0.25,0.146 10 *a
*a Approximately 10°


Turn the crankshaft approximately 10° counterclockwise.


Hide 16.REMOVE TIMING CHAIN COVER TIGHT PLUG

Hide 17.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A249934

Hold the hexagonal portion of the camshaft with a wrench and remove the bolt from the camshaft.

NOTICE:

Be careful not to damage the cylinder head or spark plug tube with the wrench.



b.
A249936

Separate the camshaft timing gear assembly from the camshaft.


c.
A249937
1.177,2.969 1.385,3.135 0.208,0.167 10 false *1 2.719,2.052 2.927,2.219 0.208,0.167 10 false *1 1.229,2.052 1.438,2.219 0.208,0.167 10 false *2 2.76,2.969 2.969,3.135 0.208,0.167 10 false *2
*1 Narrow
*2 Wide


Remove the timing chain from the camshaft timing gear assembly, and turn the camshaft timing gear assembly approximately 180°.


d.
A249938

Remove the camshaft timing gear assembly.

NOTICE:

Do not disassemble the camshaft timing gear.



Hide 18.REMOVE CAMSHAFT BEARING CAP

a.
A284105
0.563,1.823 0.719,2.021 0.156,0.198 10 1 0.604,0 0.76,0.198 0.156,0.198 10 2 0.167,1.125 0.323,1.323 0.156,0.198 10 3 2.833,0.021 2.99,0.219 0.156,0.198 10 4 2.938,1.531 3.094,1.729 0.156,0.198 10 5 1.167,0.031 1.323,0.229 0.156,0.198 10 6 1.146,1.542 1.302,1.74 0.156,0.198 10 7 2.281,0.021 2.438,0.219 0.156,0.198 10 8 2.333,1.531 2.49,1.729 0.156,0.198 10 9 1.688,0.021 2,0.219 0.313,0.198 10 10 1.688,1.542 2,1.74 0.313,0.198 10 11

Using several steps, remove the 11 bearing cap bolts in the sequence shown in the illustration.


b.
A284106
0.552,1.938 0.708,2.135 0.156,0.198 10 1 0.594,0.313 0.75,0.51 0.156,0.198 10 2 2.948,1.781 3.104,1.979 0.156,0.198 10 3 2.885,0.354 3.042,0.552 0.156,0.198 10 4 1.125,1.792 1.281,1.99 0.156,0.198 10 5 1.156,0.344 1.313,0.542 0.156,0.198 10 6 2.344,1.792 2.5,1.99 0.156,0.198 10 7 2.313,0.344 2.469,0.542 0.156,0.198 10 8 1.74,1.781 1.896,1.979 0.156,0.198 10 9 1.698,0.344 2.01,0.542 0.313,0.198 10 10

Using several steps, remove the 10 bearing cap bolts in the sequence shown in the illustration.


c.

Remove the 5 camshaft bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 19.REMOVE CAMSHAFT

a.
A249939

Remove the camshaft from the camshaft housing.


Hide 20.REMOVE NO. 2 CAMSHAFT

a.
A249940

Hold up the chain and remove the No. 2 camshaft from the camshaft housing.


b.
A249941

Suspend the chain with a string or equivalent as shown in the illustration.

NOTICE:

Be careful not to drop the chain inside the timing chain cover.



Hide 21.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A250991

Remove the flange bolt and camshaft timing exhaust gear assembly.

NOTICE:

Do not disassemble the camshaft timing exhaust gear.