Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL
RM30B0U _51 Engine / Hybrid System _009173 2AR-FE ENGINE MECHANICAL _0050874 REAR CRANKSHAFT OIL SEAL A

2AR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR ENGINE OIL SEAL

a.

Apply MP grease to the lip of a new oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the oil seal.

·

Do not allow MP grease to contact the dust seal.




b.
A195810
1.25,1.396 2.042,1.938 2.042,1.938 1.844,1.26 true 2.115,1.896 2.521,2.073 0.406,0.177 10 SST

Using SST and a hammer, tap in the oil seal until its surface is flush with the edges of the cylinder block and crankcase.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Keep the lip of the oil seal free from foreign matter.

·

Do not tap in the oil seal at an angle.




Hide 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A195875
0.384,1.203 0.714,1.359 0.33,0.156 10 SST 0.779,1.272 0.934,1.272 0.934,1.272 1.322,1.143 false 1.238,0.738 0.934,1.272 false

Using SST, hold the crankshaft.

SST
09213-54015  
91551-80650  
09330-00021  


b.

Clean the bolts and their installation holes.


c.
A196850

Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



d.
A238741
0.938,2.396 1.031,2.396 1.031,2.396 1.229,2.146 false 1.135,3.094 1.24,3.094 1.24,3.094 1.531,2.844 false 2.135,2.677 2.052,2.677 2.052,2.677 1.865,2.146 false 0.719,2.281 0.948,2.448 0.229,0.167 10 *1 2.177,2.573 2.396,2.74 0.219,0.167 10 *3 0.917,2.979 1.135,3.146 0.219,0.167 10 *2
*1 Front Drive Plate Spacer
*2 Drive Plate and Ring Gear
*3 Rear Drive Plate Spacer
V100135

Transaxle Side


Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.

HINT:
·

The front drive plate spacer is reversible.

·

As the rear drive plate spacer and the drive plate and ring gear are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.




e.
A192239
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A296877
1.781,1.698 1.917,1.865 0.135,0.167 10 2 2.333,0.917 2.469,1.083 0.135,0.167 10 4 1.583,0.417 1.719,0.583 0.135,0.167 10 1 1.083,1.115 1.219,1.281 0.135,0.167 10 3 1.188,0.74 1.323,0.906 0.135,0.167 10 5 2.281,1.344 2.417,1.51 0.135,0.167 10 6 2.125,0.521 2.26,0.688 0.135,0.167 10 7 1.323,1.583 1.458,1.75 0.135,0.167 10 8

Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.