Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM30B0U _57 Power Source / Network _009133 NETWORKING _0050933 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside combination meter assembly

·

Combination meter assembly CAN main wire or connector

·

Combination meter assembly



WIRING DIAGRAM

C280379
4.281,3.354 5.052,3.552 0.771,0.198 10 false METER 2.135,3.51 3.156,3.74 1.021,0.229 10 false from IG2 Relay 2.271,2.688 3.292,2.917 1.021,0.229 10 false from Battery 4.104,2.5 5,2.844 0.896,0.344 10 false ECU-B NO.2 5.396,2.542 6.292,2.885 0.896,0.344 10 false 40 5.396,3.385 6.292,3.729 0.896,0.344 10 false 39 5.385,4.198 6.281,4.542 0.896,0.344 10 false 21 5.677,4.354 6.573,4.698 0.896,0.344 10 false ET 5.656,3.5 6.552,3.844 0.896,0.344 10 false IG+ 5.667,2.698 6.563,3.042 0.896,0.344 10 false B 5.667,1.469 6.563,1.813 0.896,0.344 10 false CANL 5.656,0.646 6.552,0.99 0.896,0.344 10 false CANH 5.375,1.198 6.271,1.542 0.896,0.344 10 false 31 5.385,0.688 6.281,1.031 0.896,0.344 10 false 32 1.542,0.677 2.438,1.021 0.896,0.344 10 false 1*1, 9*2 1.542,1.229 2.438,1.573 0.896,0.344 10 false 2*1, 20*2 0.25,1.708 1.365,2.031 1.115,0.323 10 false G128*1 0.25,1.885 2.302,2.219 2.052,0.333 10 false No. 2 CAN Junction Connector*1 0.323,4.927 2.375,5.26 2.052,0.333 10 false *1: for 2 Pin Connector Type 0.323,5.26 2.375,5.594 2.052,0.333 10 false *2: for 22 Pin Connector Type 5.448,4.958 6.344,5.302 0.896,0.344 10 false G16 5.458,5.115 6.646,5.51 1.188,0.396 10 false Combination Meter Assembly 0.25,2.344 2.302,2.677 2.052,0.333 10 false No. 4 CAN Junction Connector*2 0.24,2.198 1.354,2.521 1.115,0.323 10 false G134*2

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 51 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)
a.
C221258
1.521,0.333 1.927,0.615 0.406,0.281 1.25,2 1.521,2 1.521,2 1.677,1.323 true 1.052,1.781 1.292,1.781 1.292,1.781 1.615,1.302 true 0.073,0.052 0.24,0.24 0.167,0.188 10 *a 0.635,1.688 1.063,1.844 0.427,0.156 10 CANH 0.875,1.906 1.271,2.063 0.396,0.156 10 CANL 1.583,0.375 1.906,0.563 0.323,0.188 10 G16
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-32 (CANH) - G16-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C221258
1.479,0.313 1.906,0.563 0.427,0.25 2.469,1.344 2.646,1.51 2.646,1.51 2.833,1.51 true 0.635,1.563 0.865,1.563 0.865,1.563 1.01,1.344 true 0.667,1.052 0.896,1.052 0.896,1.052 1.083,1.313 true 0.156,0.083 0.469,0.24 0.313,0.156 10 *a 1.552,0.365 1.833,0.573 0.281,0.208 10 G16 0.49,1.479 0.646,1.677 0.156,0.198 10 B 2.885,1.417 3.229,1.594 0.344,0.177 10 ET 0.417,0.958 0.76,1.135 0.344,0.177 10 IG+
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G16-40 (B) - Body ground Always 11 to 14 V
G16-39 (IG+) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E16-21 (ET) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR