Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING
RM30B0U _59 Vehicle Exterior _009441 EXTERIOR PANELS / TRIM _0051139 WHEEL OPENING MOULDING A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT BUMPER COVER

Hide 3.REMOVE FRONT FENDER MUDGUARD LH (w/ Mudguard)

a.
B341056

Remove the clip.


b.

Remove the 3 screws and front fender mudguard LH.


Hide 4.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH

HINT:

When removing the front fender moulding, heat the vehicle body and front front fender moulding using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Fender Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or front fender moulding excessively.


a.
B340202
1.292,0.604 1.656,0.604 1.656,0.604 1.656,0.26 true 2.563,0.5 2.917,0.5 true 0.75,1.219 1.76,1.219 1.76,1.219 1.76,0.896 true 1.104,1.208 1.104,0.938 true 1.698,1.542 1.979,1.542 1.979,1.542 2.323,2.021 true 2.938,0.406 3.25,0.563 0.313,0.156 10 *1 1.146,0.531 1.458,0.688 0.313,0.156 10 *2 0.594,1.135 0.906,1.292 0.313,0.156 10 *3 1.552,1.458 1.865,1.615 0.313,0.156 10 *4
*1 Protective Tape
*2 Double-sided Tape
*3 Clip A
*4 Clip B


Remove the 2 clips labeled A and clip labeled B.


b.

Put protective tape around the front fender moulding sub-assembly LH.


c.

Using a moulding remover, detach the 8 clips.


d.

Detach the double-sided tape to remove the front fender moulding sub-assembly LH.


Hide 5.REMOVE REAR WHEEL HOUSE FRONT PLATE LH

B338495

a.

Remove the screw.


b.

Detach the clip and rear wheel house front plate LH.


Hide 6.REMOVE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH

HINT:

When removing the quarter outside moulding, heat the vehicle body and quarter outside moulding using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Quarter Outside Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or quarter outside moulding excessively.


B340204
0.271,0.5 0.719,0.5 true 1.844,0.646 2.198,0.646 2.198,0.646 2.198,0.281 true 0.146,0.417 0.458,0.573 0.313,0.156 10 *1 1.698,0.552 2.01,0.708 0.313,0.156 10 *2
*1 Protective Tape
*2 Double-sided Tape


a.

Remove the 2 clips.


b.

Using a moulding remover, detach the 9 clips.


c.

Detach the double-sided tape to remove the quarter outside moulding sub-assembly LH.