Use the following procedure to troubleshoot the blind spot monitor system.
*: Use the Techstream.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage with the ignition switch off.
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Use the Techstream to check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| CAN communication system DTC is not output. |
| CAN communication system DTC is output. |
CAN communication system DTC is not output.
CAN communication system DTC is output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Refer to DTC Check / Clear for the blind spot monitor system.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR
Record or print DTCs and freeze frame data, if necessary.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>FREEZE FRAME DATA
| Proceed to |
|---|
| DTCs are output. |
| DTCs are not output. |
DTCs are output.
DTCs are not output.
Refer to DTC Check / Clear for the blind spot monitor system.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR
The current DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to DTC Check / Clear for the blind spot monitor system.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTCs are output. |
| DTCs are not output. |
Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
DTCs are output.
DTCs are not output.
Find the output DTC in Diagnostic Trouble Code Chart.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Problem Symptoms Table.
| Proceed to |
|---|
| Fault is not listed in Problem Symptoms Table. |
| Fault is listed in Problem Symptoms Table. |
If the symptom does not recur and no DTC is output, attempt to reproduce the symptoms
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Fault is not listed in Problem Symptoms Table.
Fault is listed in Problem Symptoms Table.
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Refer to Data List / Active Test.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Enter Test Mode (refer to Blind Spot Monitor Beam Axis Inspection).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK
Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT