Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM30B0U _56 Audio / Visual / Telematics _009404 PARK ASSIST / MONITORING _0051188 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a ground short in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB2 Short to GND in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning cancel switch assembly) is on.

·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time.


·

Outer rear view mirror sub-assembly LH (outer rear view mirror indicator LH)

·

Outer rear view mirror assembly LH

·

Blind spot monitor sensor LH

·

Harness or connector



WIRING DIAGRAM

E270468
0.792,2.438 3.313,2.854 2.521,0.417 10 Outer Rear View Mirror Sub-assembly LH (Outer Rear View Mirror Indicator LH) 0.979,3.729 3.458,3.948 2.479,0.219 10 Outer Rear View Mirror Assembly LH 0.969,3.563 1.281,3.76 0.313,0.198 10 J8 3.448,1.49 3.896,1.719 0.448,0.229 10 BSL+ 3.896,1.49 4.052,1.688 0.156,0.198 10 1 3.896,1.896 4.052,2.094 0.156,0.198 10 8 3.719,1.917 3.875,2.115 0.156,0.198 10 - 5.448,1.583 6.063,1.781 0.615,0.198 10 OMIL 4.948,3.719 6.844,3.958 1.896,0.24 10 Blind Spot Monitor Sensor LH 4.948,3.521 5.26,3.719 0.313,0.198 10 R1 5.24,1.49 5.396,1.688 0.156,0.198 10 4 3.063,1.49 3.219,1.688 0.156,0.198 10 1 3.073,1.896 3.229,2.094 0.156,0.198 10 2 2.906,1.573 3.135,1.802 0.229,0.229 10 + 2.917,1.969 3.073,2.167 0.156,0.198 10 -

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning cancel switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

DTCs are output

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR LH CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR LH CIRCUIT)
a.

Disconnect the R1 blind spot monitor sensor LH connector.


b.

Disconnect the J8 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J8-1 (BSL+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH
a.

Remove the outer rear view mirror sub-assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL


b.

Inspect the outer rear view mirror sub-assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Temporarily replace the outer rear view mirror assembly LH with a new or normally functioning one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
Result:
Proceed to
No DTCs are output
DTCs are output




No DTCs are output

END (OUTER REAR VIEW MIRROR ASSEMBLY LH IS DEFECTIVE)

DTCs are output

REPLACE OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH