Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM30B0U _56 Audio / Visual / Telematics _009404 PARK ASSIST / MONITORING _0051188 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Main Switch Circuit  


DESCRIPTION

When the blind spot monitor main switch (warning cancel switch assembly) is turned on, a signal is sent to the blind spot monitor sensor LH and the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly) illuminates. The blind spot monitor system operates according to this signal.

WIRING DIAGRAM

E271219
0.385,0.958 1.74,1.198 1.354,0.24 10 from IG1 NO. 2 Relay 2.302,1.177 3.073,1.375 0.771,0.198 10 GAUGE 2.969,1.74 5.188,2.156 2.219,0.417 10 Blind Spot Monitor Main Switch (Warning Cancel Switch Assembly) 2.958,1.521 3.417,1.719 0.458,0.198 10 G75 5.688,1.885 6,2.083 0.313,0.198 10 R1 5.698,2.094 6.875,2.448 1.177,0.354 10 Blind Spot Monitor Sensor LH 3.375,0.854 3.688,1.052 0.313,0.198 10 11 4.615,0.74 4.927,0.938 0.313,0.198 10 12 4.646,1.042 4.802,1.24 0.156,0.198 10 8 4.417,1.135 4.573,1.333 0.156,0.198 10 D 4.406,0.844 4.563,1.042 0.156,0.198 10 E 3.656,0.958 3.813,1.156 0.156,0.198 10 B 5.667,1.042 5.823,1.24 0.156,0.198 10 8 5.667,0.729 5.823,0.927 0.156,0.198 10 3 5.875,0.823 6.49,1.021 0.615,0.198 10 BIND 5.875,1.135 6.49,1.333 0.615,0.198 10 BSSW

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)
a.

Check that the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly) illuminates normally when the blind spot monitor main switch (warning cancel switch assembly) is turned from off to on.


b.

Check that the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly) turns off normally when the blind spot monitor main switch (warning cancel switch assembly) is turned from on to off.


Result:
Proceed to
The blind spot monitor indicator operates normally
The blind spot monitor indicator does not operate normally



The blind spot monitor indicator operates normally

2.READ VALUE USING TECHSTREAM

The blind spot monitor indicator does not operate normally

6.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)
2.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Blind spot monitor Master / Data List.


e.

According to the display on Techstream, read the Data List.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor main switch (warning cancel switch assembly) OFF or ON ON: Blind spot monitor main switch (warning cancel switch assembly) on
OFF: Blind spot monitor main switch (warning cancel switch assembly) off
-
Body Electrical > Blind Spot Monitor Master > Data List
Tester Display
Main Switch
50003 313 2
Result:
Result Proceed to
The display does not change as shown above when the blind spot monitor main switch (warning cancel switch assembly) is operated. A
The display changes as shown above when the blind spot monitor main switch (warning cancel switch assembly) is operated. B




A

3.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

3.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)
a.

Remove the blind spot monitor main switch (warning cancel switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR CROSS TRAFFIC ALERT BUZZER>REMOVAL


b.

Inspect the blind spot monitor main switch (warning cancel switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)
a.

Disconnect the G75 blind spot monitor main switch (warning cancel switch assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G75-11 (B) - Body ground Ignition switch ON 11 to 14 V
G75-11 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the R1 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-8 (BSSW) - G75-8 (D) Always Below 1 Ω
R1-8 (BSSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)
a.

Remove the blind spot monitor main switch (warning cancel switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR CROSS TRAFFIC ALERT BUZZER>REMOVAL


b.

Inspect the blind spot monitor main switch (warning cancel switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the R1 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-3 (BIND) - G75-12 (E) Always Below 1 Ω
R1-3 (BIND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR