Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM30B0U _59 Vehicle Exterior _009875 DOOR / HATCH _0054287 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSTALL REAR DOOR PANEL CUSHION

a.

Install a new rear door panel cushion.


Hide 2.INSTALL REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 3.INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH

Hide 6.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 7.INSTALL REAR DOOR FRAME GARNISH LH

a.

Attach the claw to install the rear door frame garnish LH.


Hide 8.INSTALL REAR DOOR WEATHERSTRIP LH

a.

Attach the 19 clips to install the rear door weatherstrip LH.


Hide 9.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door check assembly LH.


b.

When reusing a bolt labeled B:

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B337398
2.115,1.417 2.323,1.563 false 1.573,1.438 1.75,1.604 false 1.552,0.833 1.75,0.844 false 1.75,1.625 2.063,1.823 0.313,0.198 10 *1 2.344,1.573 2.656,1.771 0.313,0.198 10 *2 1.781,0.76 2.094,0.958 0.313,0.198 10 *1
*1 Bolt A
*2 Bolt B


Install the door check to the door panel with the 2 bolts labeled A.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.

Install the rear door check assembly with the 2 bolts labeled B.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 10.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B341569
0.094,1.844 0.354,2.052 0.26,0.208 10 *A 0.042,0.042 0.354,0.24 0.313,0.198 10 *B
*A Outside
*B Inside


Apply MP grease to the sliding area of the rear door outside handle frame sub-assembly LH.


b.

Attach the claw to install the rear door outside handle frame sub-assembly LH.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 11.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the rear door front outside handle pad.


Hide 12.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the rear door rear outside handle pad.


Hide 13.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door outside handle assembly LH.


b.
B337403

Install the rear door outside handle assembly LH by moving it in the direction indicated by the arrow shown in the illustration.

NOTICE:

If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.



Hide 14.INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

a.

Using a T30 "TORX" socket wrench, tighten the screw to install the rear door outside handle cover LH.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 15.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the rear door inside locking cable assembly LH.


b.

Attach the 3 claws to close the cover.


Hide 16.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the rear door lock remote control cable assembly LH.


b.

Attach the claw to close the cover.


Hide 17.INSTALL REAR DOOR WITH MOTOR LOCK ASSEMBLY LH

Hide 18.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

a.

Install the rear door lock child protection cover LH.


Hide 19.INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 20.INSTALL REAR DOOR STIFFENER CUSHION LH

HINT:

When installing the rear door stiffener cushion LH, heat the rear door panel using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the rear door panel excessively.


a.

Clean the rear door panel surface.

i.

Using a heat light, heat the rear door panel surface.


ii.

Remove the double-sided tape from the rear door panel.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear door stiffener cushion LH.

i.

Using a heat light, heat the rear door stiffener cushion LH.


ii.

Remove the peeling paper from the face of the rear door stiffener cushion LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the rear door stiffener cushion LH with the 2 bolts.

HINT:

Press the rear door stiffener cushion LH firmly to install it.


Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)



Hide 21.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 22.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating areas of the rear door window regulator.


b.

Temporarily install the temporary bolt to the rear door window regulator.


c.
B337384
1.75,0.542 1.917,0.375 false 2.552,1.5 2.792,1.74 0.24,0.24 10 (1) 3.083,0.781 3.323,1.021 0.24,0.24 10 (2) 3.083,1.302 3.302,1.563 0.219,0.26 10 (3) 1.833,0.49 2.042,0.677 0.208,0.188 10 (4) 1.958,0.271 2.177,0.438 0.219,0.167 10 *1
*1 Temporary Bolt


Install the rear door window regulator with the 3 bolts, and then tighten the temporary bolt.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the rear door window regulator as it may become damaged.



d.

Connect the connector.


Hide 23.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.
B337406
0.448,1.281 0.25,1.167 false 2.917,1.313 3.125,1.167 false 0.135,0.26 0.448,0.417 0.313,0.156 10 *A 3,0.25 3.208,0.427 0.208,0.177 10 *B 0.052,1.052 0.25,1.25 0.198,0.198 10 *a 3.167,1.083 3.385,1.333 0.219,0.25 10 *a 0.583,0.635 0.74,0.833 0.156,0.198 10 A 2.844,0.583 3,0.781 0.156,0.198 10 B
*A Front Side
*B Rear Side
*a Edge of curved surface


Install a new rear door glass channel filler to the rear door glass as shown in the illustration.

Standard:
Area Dimension
A 42 mm (1.65 in.)
B 12 mm (0.472 in.)



Hide 24.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

a.

Apply soapy water to the inside of the rear door glass channel sub-assembly LH.


b.
B337407
2.917,1.302 3.125,1.167 false 0.448,1.281 0.281,1.198 false 0.167,0.26 0.479,0.417 0.313,0.156 10 *A 3.021,0.26 3.333,0.417 0.313,0.156 10 *B 0.104,1.073 0.292,1.271 0.188,0.198 10 *a 3.167,1.083 3.375,1.333 0.208,0.25 10 *a 0.552,0.604 0.708,0.802 0.156,0.198 10 A 2.833,0.583 2.99,0.781 0.156,0.198 10 B
*A Front Side
*B Rear Side
*a Edge of curved surface


Using a plastic-faced hammer, tap the rear door glass channel sub-assembly LH onto the rear door glass sub-assembly LH to install the rear door glass channel sub-assembly LH as shown in the illustration.

Standard:
Area Dimension
A 42 mm (1.65 in.)
B 12 mm (0.472 in.)


NOTICE:

To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.



Hide 25.INSTALL REAR DOOR GLASS RUN LH

a.

Install the front side of the rear door glass run.


Hide 26.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.

Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.


b.

Connect the cable to the negative (-) battery terminal.


c.

Operate the rear door window regulator so that the rear door glass can be installed.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Remove the rear power window regulator switch assembly with rear door armrest base panel.


f.
B341354
0.333,1.677 0.646,1.677 0.646,1.677 0.771,1.74 false 0.781,1.594 0.656,1.677 false 1.833,0.896 1.688,0.896 1.688,0.896 1.594,1.031 false 1.698,0.896 1.594,0.698 false 1.354,1.927 1.49,2.104 0.135,0.177 10 A 1.885,0.792 2.073,0.979 0.188,0.188 10 *1 2.219,1.927 2.375,2.094 0.156,0.167 10 B 0.542,1.938 0.708,2.104 0.167,0.167 10 C 0.156,1.615 0.385,1.823 0.229,0.208 10 *1
*1 MP Grease


Apply MP grease to the sliding area of the rear door glass channel as shown in the illustration.

Standard:
Area Specified Condition
A 157 mm (6.18 in.)
B 25 mm (0.984 in.)
C 5 mm (0.197 in.)



g.
B337402

Slide the rear door glass sub-assembly LH to install it as shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 27.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.

Install the rear door quarter window weatherstrip LH to the rear door quarter window glass LH.


Hide 28.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

a.

Install the rear door quarter window glass LH.


Hide 29.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.

Align the rear door glass run with the rear door window division bar.


b.

Insert the rear door window division bar together with the rear door glass run into the rear door panel.


c.

Install the screw and 2 bolts.

Torque:
Screws : 3.6 N*m (37 kgf*cm, 32 in.*lbf)
Bolt : 6.2 N*m (63 kgf*cm, 55 in.*lbf)


d.

Finish installing the upper side of the rear door glass run.


Hide 30.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the rear door panel.


b.
B341350
0.385,0.427 0.25,0.427 false 3.01,0.365 2.927,0.271 false 0.104,0.333 0.313,0.563 0.208,0.229 10 *a 2.771,0.135 2.99,0.375 0.219,0.24 10 *a
*a Reference Point


Pass the rear door inside locking cable, rear door lock remote control cable and wire harness through a new rear door service hole cover, and then attach the rear door service hole cover using the reference points on the rear door panel.

NOTICE:
·

Securely install the rear door service hole cover to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the rear door service hole cover.

·

After installing the rear door service hole cover, check the seal quality.




Hide 32.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B337401

Install the rear door inner glass weatherstrip LH to the rear door trim board sub-assembly LH and fold down the 6 claws in the directions indicated by the arrows in the illustration.


Hide 33.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.

Attach the 2 claws and guide to install the rear door inside handle sub-assembly LH.


Hide 34.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.

Connect the rear door lock remote control cable LH and rear door inside locking cable LH.


b.

Engage the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH to the 2 clamps.


c.

Attach the 8 clips to install the rear door trim board sub-assembly LH.


d.

Install the 3 screws.


Hide 35.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

a.

Attach the 3 claws to install the rear door inside handle bezel plug LH.


Hide 36.INSTALL DOOR ASSIST GRIP COVER LH

a.

Attach the 5 claws, 2 clips and guide to install the door assist grip cover LH.


Hide 37.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 38.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.

Attach the 5 claws, 2 guides and 2 clips to install the rear power window regulator switch assembly with rear door armrest base panel.


Hide 39.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 41.CHECK POWER DOOR LOCK CONTROL SYSTEM