Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM30B0U _59 Vehicle Exterior _009875 DOOR / HATCH _0054296 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·
B276679
0.621,1.754 0.818,1.944 0.197,0.19 10 *1 2.535,1.754 2.732,1.944 0.197,0.19 10 *2
*1 Centering Bolt
*2 Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT BACK DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements of areas A to G are within the standard ranges.

B336853
0.917,0.24 1.073,0.438 0.156,0.198 10 A 1.469,0.542 1.625,0.74 0.156,0.198 10 B 3.396,0.24 3.552,0.438 0.156,0.198 10 C 3.938,0.458 4.094,0.656 0.156,0.198 10 D 6.49,1.042 6.646,1.24 0.156,0.198 10 E 6.667,2.51 6.823,2.708 0.156,0.198 10 F 6.708,3.938 6.865,4.135 0.156,0.198 10 G

Standard Clearance
Area Measurement Area Measurement
A 6.0 to 9.0 mm (0.236 to 0.354 in.) B -0.5 to 2.5 mm (0.0196 to 0.0984 in.)
C 6.0 to 9.0 mm (0.236 to 0.354 in.) D -0.5 to 2.5 mm (0.0196 to 0.0984 in.)
E
(Reference)
3.35 to 7.35 mm (0.132 to 0.290 in.) F
(Reference)
3.5 to 7.5 mm (0.138 to 0.295 in.)
G 3.7 to 6.7 mm (0.147 to 0.264 in.) - -


Hide 2.REMOVE DECK BOARD ASSEMBLY (for Compact Spare Tire)

Hide 3.REMOVE DECK BOARD ASSEMBLY (for Full Size Spare Tire)

Hide 5.REMOVE REAR FLOOR FINISH PLATE (for Compact Spare Tire)

Hide 6.REMOVE REAR DECK TRIM COVER (for Full Size Spare Tire)

Hide 7.ADJUST BACK DOOR PANEL SUB-ASSEMBLY

a.
B336854

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
B336855

Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


d.

Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 8.INSTALL REAR DECK TRIM COVER (for Full Size Spare Tire)

Hide 9.INSTALL REAR FLOOR FINISH PLATE (for Compact Spare Tire)